manualshive.com logo in svg

Fluke 729 Pro, User Manual

Share
Download
Fluke 729 Pro User Manual Download Page 45

Automatic Pressure Calibrator

Communication with a PC

39

Communication with a PC

Download procedures from a PC to the Product and upload test results to a PC from the 
Product. A PC, Microsoft Windows, USB cable (supplied), and Fluke 

DPCTrack2

™ 

application software, or a qualified Fluke partner’s software are required. See the 

DPCTrack2 Users Manual

 for further instructions. See Figure 

16

 for the connection.

Download DPCTrack2 Trial Version Software and the 

DPCTrack2 Users Manual 

from 

www.fluke.com/productinfo

.

Figure 16. Connection to a PC

Battery

The Product features a rechargeable battery. Charge the battery while it is inside or 
outside of the Product. This allows you to have more than one fully-charged battery.

Charge the Battery

Before you use the Product, charge the battery. To charge the battery while in the 
Product, connect the battery charger to the Product. The battery fully charges in 8 hours. 

To charge the battery outside of the Product:

1. See Figure 

17

 for battery access.

2. Place the Product face down.

3. Unlock the two fasteners to release the battery door.

USB Port 

USB Port

Summary of Contents for 729 Pro



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands