Fluke 1620A DEWK Getting Started Download Page 7

1 Before You Start

Symbol

Description

The European Waste Electrical and Electronic Equipment (WEEE) Directive (2002/96/

EC)  mark.

Safety Information

Use this instrument only as specified in this manual. Otherwise, the protection provided by the 

instrument may be impaired.

The following definitions apply to the terms “WARNING” and “CAUTION”.

“WARNING” identifies conditions and actions that may pose hazards to the user.

“CAUTION” identifies conditions and actions that may damage the instrument being used.

WARNINGS

To avoid personal injury, follow these guidelines.

DO NOT 

use this unit in environments other than those listed in the User’s Guide.

Follow all safety guidelines listed in the User’s Guide.
Calibration equipment should only be used by trained personnel.
The AC adapter can present safety concerns if misused or damaged. To avoid the risk 

of electric shock or fire, do not use the AC adapter outdoors or in a dusty, dirty, or wet 

environment. If the cord, case, or plug of the adapter is damaged in any way, discontinue 

its use immediately and have it replaced.
Never disassemble the AC adapter. Use only the AC adapter provided with the instrument 

or equivalent adapter recommended by the manufacturer of this instrument.
The AC adapter has circuits with high voltage inside that could present danger of 

electrical shock or fire if exposed. If the AC adapter is damaged in any way or becomes 

hot, discontinue its use immediately, disconnect it from any AC supply, and have it 

replaced. Do not attempt to open, repair, or continue using a damaged or defective AC 

adapter.
The instrument battery can present danger if not handled properly. To avoid the risk of 

exposure to dangerous substances or explosion, immediately remove the battery and 

discontinue use if it leaks or becomes damaged. Never allow the battery to be shorted, 

heated, punctured, or dropped. If the instrument is physically damaged, immediately 

remove the battery to insure that it does not become shorted. While removed from the 

instrument, store the battery in a location so that it will not come into contact with 

metal or fluids that might short circuit the battery and where it is safe from excessive 

temperatures.
Used batteries must be disposed of properly. Check your local regulations for additional 

information. Never dispose of batteries in fire which may result in explosion with the 

possibility of personal injury or property damage.

Summary of Contents for 1620A DEWK



























Reviews: