FlowLine EchoPod DL24 Series Quick Start Manual Download Page 3

Page: 3 / 6

We do Your Level Best

Wiring the EchoPod

After mounting the EchoPod

, make the necessary electrical connections. A wiring

diagram with specific recommendations for the sensor’s configuration can be printed

from the WebCal program. A typical wiring diagram is shown on the next page.

Red

and

Black

leads are for connection to a 24 VDC power supply or to a 4-20 mA

loop power source. The red and black wires can be extended more than 1000 feet

using 22 gauge or larger wire, however do not extend the green and white wires.

White

and

Green

leads are reserved for use with WebCal and should not be

connected during usage in the application. These wires should not be connected to

WebCal while power is supplied from any source other than the LI99 FOB.

Never allow the white or green wires to touch any power supply.

Blue

Orange

Yellow

and

Purple

wires are the relay contacts (normally open) from

each of the relays respectively.

The

Brown

wire is the common for all of the relays.

Configuring the EchoPod

Configuration of your EchoPod

should be performed prior to mounting, since it

requires connection to your PC.

Step 1: Install the WebCal Software

Download WebCal from

www.flowline.com

onto a PC with the following minimum

specifications:

Windows

2000/XP/Vista/7, 10 MB storage space, 256 MB RAM, 1 USB 2.0 port

Double-click the WebCal icon to install before proceeding to Step 2. You must have

an active Internet connection to install WebCal, as it will automatically verify driver

updates.

Step 2: Connect the USB Fob

NOTE

: Do not connect the Fob until after you’ve installed WebCal.

The EchoPod

communicates to its configuration software through the USB Fob.

Prior to connecting the Fob, ensure that all external power is disconnected from the

EchoPod

as power is provided through the PC’s USB 2.0 port. Do not use a cable

connecting the EchoPod

to the Fob any longer than 15 feet.

1) Connect the red, green, white,

and black wires from the

EchoPod

to the corresponding

colored terminals on the Fob
(as shown in the diagram).

2) Tighten the terminal screws with

a slotted screwdriver.

3) Plug the Fob into your PC’s

USB port.

Spec Tech Industrial Electric

www.spectechind.com

888-773-2832

Spec Tech Industrial Electric

www.spectechind.com

888-773-2832

Summary of Contents for EchoPod DL24 Series







Search results

Summary of Contents for EchoPod DL24 Series

Reviews:

Brands by name

Popular brands

FlowLine EchoPod DL24 Series, Quick Start Manual

Search results

Summary of Contents for EchoPod DL24 Series

Reviews:

Brands by name

Popular brands