manualshive.com logo in svg

Flomotion Systems LT260, Operation And Maintenance Manual

Share
Download
Flomotion Systems LT260 Operation And Maintenance Manual Download Page 3

 

3 

TABLE OF CONTENTS 

 

1.

 

SYSTEM INTRODUCTION ................................................................................................. 4

 

1.  Receiving and Inspection of Product and Packaging.......................................................... 4 
2.  Safety and Operation........................................................................................................... 4 
3.  Warranty ............................................................................................................................. 4 

2.

 

TECHNICAL SPECIFICATIONS ....................................................................................... 5

 

3.

 

INSTALLATION.................................................................................................................... 6

 

1.   General ................................................................................................................................ 6 

4.

 

WIRING & POWER .............................................................................................................. 8

 

5.

 

INITIAL START-UP & DISPLAY....................................................................................... 9

 

6.

 

PROGRAMMING ................................................................................................................ 10

 

PROGRAMMING MODE ..................................................................................................... 12 

[P01] Measurement Type.................................................................................................. 12 
[P02] Unit of Measure ...................................................................................................... 12 
[P03] Display Measurement Value ................................................................................... 12 
[P04] Empty Distance ....................................................................................................... 12 
[P05] Dead Zone ............................................................................................................... 13 
[P06] 4mA Set Point ......................................................................................................... 13 
[P07] 20mA Set Point ....................................................................................................... 13 
[P08] mA Fail-Safe Value ................................................................................................ 13 
[P09] mA Fail-Safe Time.................................................................................................. 13 
[P10] Dampening .............................................................................................................. 14 
[P11] Detection Threshold Voltage .................................................................................. 14 
[P12] Output Power .......................................................................................................... 14 
[P13] Sound Velocity........................................................................................................ 15 
[P14] Vapor Temperature Compensation ......................................................................... 15 
[P15] Detection Algorithm ............................................................................................... 15 
[P16] Detection Target...................................................................................................... 15 
[P17] Current Output Simulation...................................................................................... 16 
[P18] Password ................................................................................................................. 16 

7.

 

MAINTENANCE .................................................................................................................. 16

 

 
 
 
 
 
 
 
 
 

Summary of Contents for LT260



















Reviews:

No comments

Brands by name

Popular brands

Load more brands