FLO-DYNAMICS TTCF-9A Quick Start Instructions Download Page 2

 

TTCF-9A 

Variable High Flow Heated 

Hydraulic Component Flusher

 

40201409 

QUICK START 

INSTRUCTIONS 

 

Flo-Dynamics, Inc.  •  3300 Reedy Drive  •  Elkhart, IN 46514  •  800-303-5874

 

 

 

 

          

       

Page 

2

 of 

5

 

Connect the red service hose to the cooler inlet line and the 

blue service hose to the return line of the cooling system.  
Once the unit reaches 140 degrees, press the STOP 

button. 
Press the manual air purge button to clean out the lines. 
Remove the top half of the filter housing and place the 

screen filter into a waste bucket/container. 
Move the Flow Control Valve to position 4
Use the MODE button to select “START PURGE”. This will 

run the initial purge for 7.5 seconds to purge the cooler and 

line with clean fluid. Repeat until clean fluid is observed.  
Clean the screen filter if needed, and reassemble the filter 

housing. 
Move the Reverser Valve toward the blue hose coming 

from the cooling system’s return line. This will backflush the 

cooling system.  

 

 

 

 

 

 

Use the MODE button to select “START FLUSH”. Use the 

RUN TIME button to select the flush cycle time. It is 

suggested that the initial flush runs for 15 minutes to 

capture initial contaminants within the cooler system. 
Press START/PAUSE and check the following: 

o

 

Secure fill cap 

o

 

Secure filter screen 

o

 

Check fluid level 

o

 

Check all connections 

o

 

Set flow rate 

o

 

Set flow direction 

Press the START/PAUSE button to start the flush cycle. 
At the end of a flush cycle, the flusher will stop and signal 

with an audible sound. The display will show “FLUSH 

COMPLETE” with before and after flush cycle results.  
Press the manual air purge button to clean out the lines. 
Remove the top half of the filter housing, note debris on 

filter screen, clean the screen, and reassemble the filter 

housing. 
Repeat flush cycle selecting a desired time using the RUN 

TIME button from 15-120 minutes. 
NOTE: With an initial flush completed, you can now run 

longer flush cycles along with switching the flow direction 

using the reverser valve between flush cycles. 
Move the Reverser Valve toward the red service hose. 
Use the MODE button to select “START FLUSH”. 

 

 

 

 

 

 

 

 

 

Summary of Contents for TTCF-9A






Reviews: