Analog
MPX
Connect to the included
power pigtail or a 12V
DC power adapter
(not included).*
Image Sensor
1/3” 1.3MP CMOS
Video Format
NTSC (C233BC)/PAL (C233BCP)
Effective Pixels
H: 1305 V: 1049
Resolution
Digital: 720p
Analog: 960H
Scan System
Progressive
Sync System
Internal
S / N Ratio
≥
50dB (AGC Off)
Iris
AES
AES Shutter Speed
1/60 (1/50) ~ 1/60,000 sec.
Min. Illumination
0.1 LUX (IR Off)
0 LUX (IR LEDs On)
Video Output
Digital: 720p MPX HD-CVI
Analog: Composite 1.0Vpp @
75ohm
Lens Focal Length / Type
3.6mm F2.0 / Fixed
FOV (Horizontal)
Digital: 78°
Analog: 78°
Termination
BNC Type
IR Range / Qty.
70ft / 21m; 24 IR LED’s
Power Requirement
12V DC ± 10%
Power Consumption
380mA MAX with IR LED
Operating Temp. Range
–22° ~ 140°F / –30° ~ 60°C
Environmental Rating
IP66
Dimensions (W x H x D)
2.8” x 2.8” x 8.0”
72mm x 72mm x 204mm
Weight (including stand)
0.9lbs / 0.4kg
Camera Dimensions
Camera Specifications
To install the camera:
1. Use the included mounting template to mark and drill
holes for the included mounting screws.
NOTE:
Insert the included drywall anchors if installing into
drywall.
2. Connect the video and power cable as detailed in the
section ‘Setting up the Camera’.
3. Attach the camera
base to the mouting
surface using the
included screws.
4. Set the position and angle of the camera using the
provided Allen key.
5. Remove the protective film from the camera lens.
Setting up the Camera
8.0”
204mm
2.8”
72mm
2.8”
72mm
ATTENTION:
Test the camera prior to selecting a permanent
mounting location by temporarily connecting the
camera(s) and cables to the DVR.
Installing the Camera
WARNING:
A REGULATED 12V DC power supply is REQUIRED for use with
this camera. Use of a non-regulated, non-conforming power
supply can damage this product and voids the warranty.
Camera Wiring
MPX
Connect to an MPX
DVR for 720p viewing
and recording.
Analog
Connect to an analog
DVR for 960H viewing
and recording.
1. Connect one of the two BNC connectors on the camera to
the video cable. See “Camera Wiring” for details.
2.
DC Power—Power Pigtail:
Connect the included power pigtail
to the camera. Connect the terminating wires of the cable
directly to the DC power source.
OR
3.
DC Power—Power Adapter:
Connect a 12V DC power adapter
(not included) to the camera and a local power outlet.
NOTE:
For pigtail connection with 12V DC, make sure to check
polarity specifications on the power adapter.
Extension Cable Options
Specification
Maximum Length
RG59 20AWG Conductor 95% Braid
CSA/UL or C(UL) Approved
Up to 1500ft (455m)
†
RG6 20AWG Conductor 95% Braid
CSA/UL or C(UL) Approved
Up to 2300ft (700m)
†
Analog CCTV Balun
Up to 300ft (91m)
† Long cable runs over 1000ft (300m) may be affected by
electro-mechanical interference (EMI), which can increase the
amount of noise in the picture in some installations.
The entire length of the cable run must be made using a
single extension cable between the camera and the DVR.
B) Loosen lower screw with
the Allen key to adjust the
camera’s vertical position.
C) Loosen upper screw with the
Allen key to rotate the camera
housing.
A) Turn the adjustment ring
to tighten / loosen the stand
connection. Adjust the
camera’s horizontal position.
A
B
C
* Camera focus may be affected if the power connection is too
long. It is recommended not to extend the power connection
past 200ft (61m).
