Flintec FT-10 FILL, Technical Manual

Page: 127 / 131

FT-10 Fill Technical Manual, Rev. 2.21, July 2020 Page 126 of 131
22. P
ARAMETER
D
EFAULT
T
ABLE
0-- Interface Block 14- Entries
00- RS 232C 142 Label No entrance
000 Data Format 3 = BSI 143 Display Refresh Rate 1 = 100ms
001 Baud rate 3 = 9600 2-- Scale Block
003 Address 0 20- Set up
004 Data length and Parity 0 = 8 bit, no parity 200 Approved 0 = No
005 Checksum 0 = Disable 201 Increased indication 0 = x10 key
006 Carriage Return 1 = Enable 203 Zero range 3 = ± %50
007 Line Feed 1 = Enable 204 Auto zero tracking 0 = Disable
008 Response Speed 0 = immediately 205 Tare 2 = Tare/Clear
01- RS 485 206 Motion detector 2 = ± 1e
010 Data Format
5 = Modbus RTU Lo-
Hi
(1)
21- Scale Build
011 Baud rate 3 = 9600 212 Capacity / d 60 kg / 0.01 kg
013 Address 1 214 Unit 0 = kg
014 Data length and Parity 0 = 8 bit, no parity 3-- Calibration Block
015 Checksum 0 = Disable 30- Calibration
016 Carriage Return 1 = Enable 301 Calibration
017 Line Feed 1 = Enable 302 Linearity Correction
018 Response Speed 0 = immediately 31- Adjustment
03- Ethernet 310 Zero adjustment
030 Ethernet Data Format
5 = Modbus RTU Lo-
Hi
311 Span adjustment
031 Ethernet Address 1 312 Span adjustment under load
032 IP Address 192.168.016.250 313 eCal Calibration
033 Subnet Mask 255.255.255.000 5-- Filling Block
034 Gateway Address 192.168.016.253 50- Filling Parameters
035 Local Port 502 500 Filling mode 1 = Mode-1
036 Response Speed 0 = immediately 501 Feeding type 1
04- Printer 502 Preact correction factor 50%
040 Print out format 2 = Multi line 503 Preact correction frequency 1
041 CN 1 = Will be printed 504 Check delay 1.0 sec.
042 Minimum print 20 505 Zeroing period 250 sec.
043 Print method 0 = With Print Key 506 Zeroing delay 2.0 sec.
044 Line feed before printing 00 = 0 F + 0 LF 507 Indication at the end of filling 0
045 Line feed after printing 04 = 0 F + 2 LF 508 Feeding check 0
046 Form feed 0 = Disable 509 Filling time 0
047 Space on the left 3 50A Start Type 0
048 Quantity of copies 1 8-- Metrological Data Block
05- Profibus DP 80- Legal Metrology
050 Data Format 0 = signed 32 bit 800 Calibration counter
051 Rack Address 0 9-- Diagnostic
06- Profinet, EtherNET/IP, EtherCAT, Powerlink 90- Tests
060 Data Format 0 = signed 32 bit 900 Key Pad testing
07- CANopen, CC-Link 901 RS 232C testing
070 Data Format 0 = signed 32 bit 902 RS 485 testing
071 Rack Address 0 903 Parallel inputs test
072 Baudrate 0 = 156 kbps
1-- Configuration Block 904 Parallel outputs test
11- Start Up 905 mV indication
116 Function key 3 = Quantitiy 99- Printing Parameters
117 Zero output 0 = Gross zero 990 Whole parameters
12- Filter 991 Load default parameters
120 Filter 7
1)Except for FT-10Fill EN