background image

ABOUT YOUR NEW FLAVEL MELODY

The Flavel inset coal effect gas fire incorporates a unique and highly developed

fuel bed which gives the realism of a loose coal layout combined with realistic

flames and glow. The use of durable ceramic material in the construction of the

fuelbed components ensures long and trouble free operation.

When first using the new fire a slight smell may be noticed. This is due to starch

used in the manufacture of the soft ceramic coals, it is non-toxic and will soon

disappear.

Please take the time to fully read these instructions as you will then be able to

obtain the most effective and safe operation of your fire.

IMPORTANT SAFETY INFORMATION

WARNING

This appliance has a naked flame and as with all heating appliances a fire-

guard should be used for the protection of children, the elderly and infirm.

Fireguards should conform to B.S. 8423 : 2002 should be fitted. (Fireguards

for use with gas heating appliances).

It is important that this appliance is serviced at least once a year by a CORGI reg-

istered gas installer and that during the service the fire is removed from the fire

opening and the chimney or flue visually checked for fallen debris or blockages

which must be removed. The chimney should also be checked to ensure clear-

ance of flue products. We recommend that during the annual service, replace-

ment of the Oxypilot is carried out.

These are conditions of the manufacturers

guarantee.

After installation or during servicing a spillage test must always be carried

out.

Rubbish of any type must NEVER be thrown onto the fuel bed, this could affect

safe operation and damage the fire.

Any debris or deposits should be removed from the fuel bed from time to time.

This may be carried out by referring to the cleaning section as described later in

this book.

Only the correct number and type of coals must be used and only complete and

genuine replacement sets must be used.

Always keep furniture and combustible materials well clear of the fire and never

dry clothing or items either on or near to the fire. Never use aerosols or flamma-

ble cleaning products near to the fire when it is in use.

3

Summary of Contents for Caress Slimeline SC FNVC**SN













Reviews: