Flair Signature PRO 2 Quick Start Manual Download Page 2

Instructions: Brewing with  

#1 - Prepare the Flair

(a) Insert post into base and place drip tray onto base. 

(b) Take apart brew head. (c) Move plunger into position 

using dosing cup. When positioned correctly plunger should 

be opposite red o-rings inside cylinder.

Before Getting Started

Using Your Pressure Gauge

Introducing Espresso!

Brewing espresso - by hand - with the Flair is a mixture of 

science and art. The Flair is like a hand tool; it will follow 

your decisions and actions. Your espresso’s taste and crema 

is most dependent on the 

quality and freshness of 

your coffee beans

 and 

finding the right grind size

.

Fresh Whole Coffee Beans Required: 

For espresso, pre-ground beans will never 

work. We recommend using coffee beans 

roasted within a few weeks of use and 

grinding immediately before brewing. 

For espresso, only use a quality burr grinder which creates 

more uniform grounds than a blade grinder and allows you 

to control your grind size. When starting, grind your coffee 

a notch or two coarser than the normal range for espresso 

and we recommend starting with 20 grams of beans 

as your dose size. Changing coffee beans may require 

changing your grind size.

How Do I Get Good Crema? 

Crema is only obtained when your espresso 

is brewed correctly. Start with brew 

temperatures between 194 - 204˚F, ensure 

your beans are freshly roasted and ground 

and that you experiment with different grind 

and dose sizes. It may take practice to get it 

right. Don’t forget, we’re here to help!

Contents of Your Signature PRO Model

 

 

1
2
3
4

5
6
7

8

1

2

3

4

9

7

8

10

Achieving Espresso Made Right with the Flair is a 

combination of the 

right grind

, the 

right pressure

and the 

right brewing time

Everything starts with the grind and dose, which creates the

resistance to achieve desired pressure and brewing time. 

“Flair-istas” who have mastered their technique will brew 

between 6 and 9 BAR at a time between 35-45 seconds.

Tip 1:

 Calibrate your grind, pressure, and time with inexpensive beans! 

Tip 3: 

Pre-wet your grounds via pre-infusion by slowly pulling 

lever down until 2 BAR is achieved, and hold still for 5-10 

seconds. Then proceed to brew as normal for 35-45 seconds. 

BREW TIME

PRESSURE

Less Than

35

Seconds

35-45

Seconds

More Than

45

Seconds

Grind 

More 

Fine

Grind 

More 

Fine

More 

Pressure

Grind 

More 

Fine

Espresso 

Made 

Right

Grind 

More 

Coarse

Grind 

More 

Coarse

Less 

Pressure

Grind 

More 

Coarse

1-5 BAR

6-9 BAR

10-12 BAR

DANGER! 

ST

OP & DISCARD GROUNDS

>12 BAR

Your Signature PRO comes with a pressure gauge to help 

ensure your espresso is to your specifications at all times. 

Burr Grinder Required:

#2 - Prepare your Beans

(a) Always use a burr grinder to grind at least 16 grams of 

freshly roasted beans. (b) Affix funnel to top of portafilter 

and fill with fresh grounds. (c) Tamp lightly with tamping cap 

below. (d) Remove the funnel and place the screen on top. 

#3 - Prepare the Brew Head

(a) Add preheat cap onto bottom (o-ring side) of cylinder 

and fill with just boiled water. Leave for at least 30 

seconds. (b) Pour out preheat water from cylinder, remove 

the preheat cap. (c) Place cylinder on top of portafilter. 

#4 - Add Brew Water

(a) Add your near-boiling brew water (194 - 204˚F) through 

top of cylinder. Fill until water is visible in the well. 

Do not 

underfill!

 (b) Affix stem by pressing down into well. Don’t 

dump excess water. (c) Rotate gauge for best visibility.

#5 - Brew with Flair

Place brew head onto the Flair and lower the lever to brew. 

For spouted brewing “click” spout on bottom of portafilter. 

Brewing time should be between 35-45 seconds at 6-9 BAR 

pressure. If this is not the case, check your grind and dose. 

(a)

(b)

(c)

(a)

(b)

(c)

(d)

(a)

(b)

(c)

(a)

(b)

(c)

Tip 2: 

Keep your dose constant when calibrating to reduce variables.

Main Post & Lever

Base

Dosing Cup & Funnel

Brew Head 

     

(portafilter, plunger, cylinder)

Screen, Preheat (Tamping) Cap 

Stainless Steel Spout

Stainless Steel Tamper

the Flair Signature PRO

Travel Case

Stainless Steel Drip Tray

Pressure Gauge & Stem

9

5

Please use the chart below to help you dial-in.

Don’t break your Flair. Never brew in the Black!

Spouted Brewing

“Click” On/Off

10

6

Reviews: