manualshive.com logo in svg

FK Motors FK 200, Manual

Share
Download
FK Motors FK 200 Manual Download Page 22

Free stroke of front brake 

The free stroke of the front brake is 10-20mm. 

Brake oil 

The brake oil is harmful to the eyes and skin. If the brake oil gets into 

eyes or onto the skin, rinse them thoroughly with clean water 

immediately and seek medical attention if irritation persist 

Check the liquid level in the front brake cylinder. If low, add appropriate 

amount of specified brake fluid. When the brake pads wear out, the  

brake oil in the cylinder will be automatically injected into the tube and  

the fluid level will decrease along with it. 

Brake pad wear limit indicator 

The key to inspection the condition of the brake pad for the front wheel is 

to check whether the brake pad wear limit indicators can be seen. If the 

wear exceeds the indicators, replace the brake pad accordingly. 

 

Lighting signal system inspection 

Turn the key of the main switch to start the engine. Check the respective 

front & rear lamps,  left & right signal lamps and horn for functionality. If  

found not working properly, send to an authorised FKM workshop for 

repairs or replacements. 

 

 

Page 21 

 

 

Summary of Contents for FK 200







































Reviews:

No comments

Brands by name

Popular brands

Load more brands