manualshive.com logo in svg

FK Motors FK 200, Manual

Share
Download
FK Motors FK 200 Manual Download Page 1

INTRODUCTION 

       

Thank you for choosing FKM. Do take some time to understand the contents of this manual before using this motorcycle. The industry-leading FK 200/200-D is a 
high-quality motorcycle designed and developed for you by our company using modern production technology. The motorcycle is of high degree technical 
performance and reliability and fully complies with the latest national emission standards. This is an environmentally-friendly motorcycle that meets the demand 
of our modern society. Using this motorcycle make your work and life, comfortable and convenient. 

 

This manual provides an overview of the correct care and maintenance methods for our motorcycles. Proper use of the motorcycle as instructed by the manual 
will keep it durable and malfunction-free. If you have any questions regarding the operation and maintenance of your motorcycle, please contact an authorised 
FKM dealer. 

We have professionally trained technicians who are ready to provide you with the best using a full range of tools and equipment. 

All configurations and parameters are for reference only. All contracts are subjected to the actual configurations of the manufacturer. 

The motorcycle is in line with GB7258 Safety Specifications for motors v  ehicles operating on the roads and the 
Q/FKMT11 Corporate Standards. 

 

 

Summary of Contents for FK 200







































Reviews:

No comments

Brands by name

Popular brands

Load more brands