Five12 Vector Sequencer User Manual Download Page 18

Page: 18 / 20

On the

Seq Ctl

page for any part, you can edit eight parameters at a

time for a single Part. The Dashboard is a series of pages that let you

edit one parameter for all eight Parts at once.

To get to the Dashboard, press

Part

to go to the

PART

page, and then

press

. The top-left of the first OLED will list the parameter being

edited (

START

step), the top-left of the second OLED will be

D-BRD

for Dashboard. Each of the values for the 8 encoders will list the Part

name and the current value for the parameter.

To change the parameter being edited, you can turn encoder

, or

press any of the white keys on the mini-keyboard. The white keys will

page through the parameters in the same order that they appear on the

SEQ CTL

page:

START

LEN

DIR

, etc.

In addition to the 8 parameters from

SEQ CTL

, there are 3 additional

parameters only available in the Dashboard. You can reach them

using encoder

, or by pressing

. These parameters are:

GATE SCL

: Scale all gate values.

VEL SCL

: Scale all velocity values.

CHAN SCL

: Scale the probability for all chance operations.

Keep in mind: These scale values affect every step for that Part.

Part

The Dashboard

Summary of Contents for Vector Sequencer





















Search results

Summary of Contents for Vector Sequencer

Reviews:

Related manuals for Vector Sequencer

Brands by name

Popular brands

Five12 Vector Sequencer, User Manual

Search results

Summary of Contents for Vector Sequencer

Reviews:

Related manuals for Vector Sequencer

Brands by name

Popular brands