manualshive.com logo in svg

Fisher D2T FloPro, Instruction Manual, Page: 2 / 16

Share
Download
Fisher D2T FloPro Instruction Manual Download Page 2

Instruction Manual

D104138X012

D2T FloPro Valve

June 2017

2

Table 1. Specifications

Valve Assembly Pressure Class

ASME B16.34 CL900

Maximum Inlet Pressure and Temperature

(1)

155 bar from -46 to 93

°

C, and 150 bar at 149

°

C.

(2250 psig from –50 to 200

°

F, and 2185 psig at

300

°

F)

Maximum Allowable Pressure Drop

(1)

Flow Down

(2)

 

Maximum Inlet Pressure: 

155 bar (2250 psig)

Maximum Outlet Pressure: 

103 bar (1500 psig)

Flow Up

Maximum Inlet Pressure: 

103 bar (1500 psig)

Maximum Outlet Pressure: 

103 bar (1500 psig)

Shutoff Classification

Class IV ANSI/FCI 70‐2 and IEC 60534‐4

Construction Materials

Valve Body and Bonnet:

 ASME SA 352 LCC

Valve Plug and Seat:

 

J

 

R30006 (Alloy 6) or 

J

 

S17400 double H1150

Valve Stem:

 S31600

O‐Rings:

 HNBR (Hydrogenated Nitrile)

Packing:

 PTFE/Carbon PTFE

Packing Springs:

 N07718

Stem Bushing:

 PPS (polyphenylene sulfide)

Actuator Diaphragm:

 Nitrile/Polyester

Actuator Springs:

 Zinc‐plated steel

Flow Characteristic

FloPro Characterized

Port Diameter

13 mm (0.5 inch)

Maximum Travel

13 mm (0.5 inch)

Approximate Weight

7.7 kg (17 lb)

Material Temperature Capabilities

Valve Body Assembly:

 -46 to 149

°

C (-50 to 300

°

F)

Actuator Assembly:

 -46 to 93

°

C (-50 to 200

°

F)

Bonnet/Body Connection

Threaded with leakoff bleed

Standard Actuator Configuration

The D2T FloPro

 

actuator is an on/off

spring‐and‐diaphragm.

Globe Valve Body: 

Supplied as either Air‐to‐Open or

Air‐to‐Close.

Maximum Actuator Casing Pressure

2.8 bar (40 psig)

Minimum Required Actuator Casing Pressure

2.1 to 2.4 bar (30 to 35 psig)

Actuator Diaphragm Effective Area

194 cm

2

 (30 square inches)

Actuator Pressure Connections

1/4 NPT internal

1. The pressure or temperature limits in the referenced tables and any applicable ASME code limitations should not be exceeded.
2. Standard flow direction.

Educational Services

For information on available courses for Fisher D2T valves, as well as a variety of other products, contact:

Emerson Automation Solutions
Educational Services - Registration
Phone: 1-641-754-3771 or 1-800-338-8158
E-mail: [email protected]
emerson.com/fishervalvetraining

Summary of Contents for D2T FloPro

















Reviews:

No comments