Fisher Scientific Mini300V Plus Instruction Manual Download Page 3

 

 

 

 

 

 

 

Warning

   

The MINI300V PLUS Power Supply has been thoroughly tested and found to 

comply within the limits of CE regulation.    It has been manufactured using the 

latest technology and does not require maintenance.    When used correctly 

this unit poses no particular health risk, although it can deliver dangerous 

voltage levels if used incorrectly.    Accordingly, this power supply must only be 

operated by fully qualified personnel adhering to the guidelines laid out within 

this instruction manual.    Although this power supply is equipped with all 

necessary safety features against abuse and accidental failure, caution should 

always be exercised when working with high voltage equipment.    Any 

individual intending to use this instrument should read the entire manual 

thoroughly before operation. 

 

1.  Read the instruction manual thoroughly before use. 

2.  Never touch the power outlets with any conductive object (e.g. naked 

metal wire) other than properly insulated power supply cables. 

3.  Do not spill liquid or insert metal objects inside the power supply. 

4.  Never block the ventilation holes or place the unit in any enclosure unless 

there is adequate ventilation; never expose the power supply to a direct 

heat source. 

5.  Never touch any part of the power supply assembly (i.e. power supply, 

cables or electrophoresis tank) before switching OFF the power supply. 

6.  Never manipulate with wet hands. 

7.  Do not connect to ground any of the power outputs or the buffer within the 

electrophoresis tank; the power outputs should be only connected to an 

insulated electrophoresis tank equipped with a safety cover. 

8.  Do not connect any power supplies in series or in parallel. 

9.  Never open the back plate or remove the cover, otherwise an electric 

shock may result.    Repairs should only be made by the manufacturer or a 

service technician authorised by the manufacturer. 

10.  Never use this power supply if the safety cover is not in position correctly. 

11.  Do not use the unit if there is any sign of damage to the external tank or 

cover.    Contact the manufacturer or supplier immediately to replace or 

Summary of Contents for Mini300V Plus


















Reviews: