background image

7

Environmental Conditions

Operating:

17°C to 27°C; 20% to 80% relative humidity, non-condensing. Installation category II
(overvoltage) in accordance with IEC 664. Pollution degree 2 in accordance with IEC 664.
Altitude Limit: 2,000 meters.

Storage:

-25°C to 65°C
10% to 85% relative humidity

Declaration of Conformity

(for 230 volt)
We hereby declare under our sole responsibility that this product conforms with the technical requirements of
the following standards:

EMC:

EN 61000-3-2

Limits for harmonic current emissions

EN 61000-3-3

Limits for voltage fluctuations and flicker

EN 61326-1

Electrical equipment for measurement, control, and laboratory use;
Part l: General Requirements

Safety:

EN 61010-1

Safety requirements for electrical equipment for measurement,
control, and laboratory use; Part I: General Requirements

EN 61010-2-010

Part II: Particular requirements for laboratory equipment for the
heating of materials (Hotplates and Stirring Hotplates)

EN 61010-2-051

Part II: Particular requirements for laboratory equipment for mixing
and stirring (Stirrers and Stirring Hotplates)

per the provisions of the Electromagnetic Compatibility Directive 2004/108/EC, and per the provisions of the
Low Voltage Directive 2006/95/EC.

The authorized representative located within the European Community is:

Thermo Fisher Scientific
Electrothermal House
Unit 12A
Purdeys Industrial Estate
Purdeys Way
Rochford, Essex, SS4 1ND
United Kingdom
Tel: +44(0)1702 303350

Copies of the Declaration of Conformity are available upon request.

S

PECIFICATIONS

Summary of Contents for 11100100H













Reviews: