background image

16

FCC Statement (United States Only)

This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment generates, 
uses and can radiate radio frequency energy and, if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications. However, there 
is no guarantee that interference will not occur in a particular installation. If this equipment 
does cause harmful interference to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try to correct the interference by 
one or more of the following measures: 
•  Reorient or relocate the receiving antenna. 
•  Increase the separation between the equipment and receiver. 
•  Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifi cations not expressly approved by the manufacturer responsible for 
compliance could void the user’s authority to operate the equipment. 
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) this device may not cause harmful interference and (2) this device must accept 
any interference received, including interference that may cause undesired operation.

Consumer Information

ICES-003

This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions: (1) this device may not cause harmful 
interference and (2) this device must accept any interference received, including interference 
that may cause undesired operation.

NMB-003

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes : (1) il ne 
doit pas produire de brouillage et (2) l’utilisateur du dispositif doit être prêt à accepter tout 
brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le 
fonctionnement du dispositif.

Summary of Contents for X6031
















Reviews: