background image

7

Battery Installation

Hint:

 We recommend using 

alkaline

 batteries for longer battery life.

Swing/Sounds Battery Installation

•  Locate the swing/sounds battery compartment on a swing housing.
•  Loosen the screws in the battery compartment door with 

a Phillips screwdriver. Remove the battery compartment door.

•  Insert four “C” (LR14) 

alkaline

 batteries into the battery compartment.

•  Replace the battery compartment door and tighten the screws 

with a Phillips screwdriver. 

1,5V x 4

“C” (LR14)

Vibration Battery Installation

•  Locate the vibration battery compartment on a swing housing.
•  Loosen the screw in the battery compartment door with a Phillips 

screwdriver. Remove the battery compartment door.

•  Insert one “D” (LR20) 

alkaline

 battery into the battery compartment.

•  Replace the battery compartment door and tighten the screw with 

a Phillips screwdriver. 

1,5V x 1

“D” (LR20)

•  If this product begins to operate erratically, you may need to reset 

the electronics. Turn the power off and then back on.

•  When motion or sounds from the product become slow/faint or 

stop, replace the batteries.

• Protect the environment by not disposing of this product 

with household waste (2002/96/EC). Check your local 
authority for recycling advice and facilities (Europe only).

Battery Safety Information 
In exceptional circumstances, batteries may leak fluids that 
can cause a chemical burn injury or ruin your product. To avoid
battery leakage:

• Do not mix old and new batteries or batteries of different types: 

alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).

• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove 

exhausted batteries from the product. Dispose of batteries safely. 
Do not dispose of this product in a fire. The batteries inside may 
explode or leak.

• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be 

charged under adult supervision.

Summary of Contents for V4826













Reviews: