background image

3

CAUTION

• In the unassembled state, this package contains small parts. Adult assembly is required.
• Use the charger in dry locations only.

WARNING

Prevent Injuries and Deaths

• Direct Adult Supervision Required
• Keep Children Within Safe Riding Areas.

These areas must be:

- away from swimming pools and other bodies of water to prevent drownings     
- generally level to prevent tipovers
- away from steps, driveways, roads and alleys.

RIDING HAZARD

WARNING

• Batteries can fall out and injure a child if vehicle tips over. Always use battery clamp.

PREVENT FIRE

- Never modify the electrical system. Alterations could cause a fire resulting in serious 

injury and could also ruin the electrical system.

- Use of the wrong type battery or charger could cause a fire or explosion resulting in 

serious injury.

- Use of Power Wheels

®

components in products other than Power Wheels

®

vehicles 

could cause overheating, fire or explosion.

• The battery must be handled by adults only. The battery is heavy and contains sulfuric 

acid (electrolyte). Dropping the battery could result in serious injury.

• Never allow children to charge the battery. Battery charging must be done by adults only.

A child could be injured by the electricity involved in charging the battery.

• Never lift or carry the battery by the wires or connector. This can damage the battery and

possibly cause a fire resulting in serious injury. Lift and carry the battery by the case only.

• Read the safety instructions on the battery.
• Examine the battery, charger and their connectors for excessive wear or damage each time

you charge the battery. If damage or excessive wear is detected, do not use the charger or
the battery until you have replaced the worn or damaged part.

HOT

motors. Handle carefully.

Warnings and Cautions

B

ELECTRICAL HAZARD

73218pr-0920.qrk  5/21/01 2:28 PM  Page 3

Summary of Contents for FISHER-PRICE 73218





































Reviews: