background image

11

Battery Installation 

• 

For longer life, use 

alkaline

 batteries.

• 

Locate the battery compartment on the dashboard. Loosen the screw in the battery 

compartment door and remove the door.

• 

Insert three AA (LR6) 

alkaline

 batteries. 

• 

Replace the battery compartment door and tighten the screw.

• 

If this toy begins to operate erratically, you may need to reset the electronics. Slide the 

power/volume switch off and back on. 

• 

When sounds/lights become faint or stop, it’s time for an adult to change the batteries.

1,5V x 3

AA (LR6)

• 

Protect the environment by not disposing of this product with household waste 

(2002/96/EC). Check your local authority for recycling advice and facilities.

Battery Safety Information

In exceptional circumstances, batteries may leak fluids that can cause a chemical burn 

injury or ruin your product. To avoid battery leakage:

• 

Do not mix old and new batteries or batteries of different types: alkaline, standard 

(carbon-zinc) or rechargeable (nickel-cadmium).

• 

Insert batteries as indicated inside the battery compartment.

• 

Remove batteries during long periods of non-use. Always remove exhausted batteries 

from the product. Dispose of batteries safely. Do not dispose of this product in a fire. 

The batteries inside may explode or leak.

• 

Never short-circuit the battery terminals.

• 

Use only batteries of the same or equivalent type, as recommended.

• 

Do not charge non-rechargeable batteries.

• 

Remove rechargeable batteries from the product before charging.

• 

If removable, rechargeable batteries are used, they are only to be charged under  

adult supervision.

Summary of Contents for DJD09













Reviews: