background image

2

!

 WARNING!

Electric Shock Hazard

Failure to follow this advice may result in 

electric shock or death.

 

z

Before carrying out any work on the electrical 

section of the appliance, it must be disconnected 

from the mains electricity supply.

 

z

Connection to a good earth wiring system is 

absolutely essential and mandatory.

 

z

Alterations to the domestic wiring system must 

only be made by a qualified electrician.

!

 WARNING!

Fire Hazard

Failure to follow this advice may result in 

overheating, burning, and injury.

 

z

Do not use adapters, reducers, or branching 

devices to connect this appliance to the mains 

power supply.

!

 WARNING!

Cut Hazard

Failure to use caution could result in injury.

 

z

Take care: some edges are sharp.

READ AND SAVE THIS GUIDE

WARNING!

To avoid hazard, follow these instructions carefully before installing or using this appliance.

 

z

Please make this information available to the person installing the appliance—doing so 

could reduce your installation costs.

 

z

This appliance must be installed and connected to the mains power supply only by a 

suitably qualified person according to these installation instructions and in compliance 

with any applicable local building and electricity regulations. Failure to install the 

appliance correctly could invalidate any warranty or liability claims.

 

z

If the power supply cable is damaged, it must be replaced by the manufacturer, its service 

agent or similarly qualified person in order to avoid a hazard.

 

z

Isolating switch: make sure this oven is connected to a circuit which incorporates an 

isolating switch providing full disconnection from the power supply in accordance with the 

wiring rules.

 

z

The oven must be earthed.

 

z

Do not use adaptors, reducers or branching devices to connect the oven to the mains 

electricity supply, as they can cause overheating and burning.

 

z

The appliance must not be installed behind a decorative door in order to avoid 

overheating.

 

z

Please take extra care not to damage the lower trim of the oven during installation. The 

trim is important for correct air circulation and allows the door to open and close without 

obstruction. The manufacturer does not accept any responsibility for damage resulting 

from incorrect installation.

SAFETY AND WARNINGS

Summary of Contents for OB60SC5LB









Reviews: