manualshive.com logo in svg

Fisher & Paykel OB60 Series, Installation Manual, Page: 10 / 12

Share
Download
Fisher & Paykel OB60 Series Installation Manual Download Page 10

9

!1

SECURE THE OVEN TO THE CABINETRY

!2

REFIT THE DOOR

IMPORTANT!

 

˜

Do not lift the oven by the door handle.

 

˜

Do not over-tighten the screws.

 

˜

Do not seal the oven into the cabinetry with silicone or glue. This makes future 
servicing difficult. Fisher & Paykel will not cover the cost of removing the oven, or 
damage caused by this removal.

1 

 Position the oven in the prepared cavity.

2 

Open the oven door fully.

3 

Secure oven to cabinetry using supplied screws.

2.5 mm

1 

Holding the door on both sides, line up 
the holes in the base of the door with 
the hinges and slide the door on.

2 

Locking the door onto the hinges (hinges may vary):

 

˜

OB60 models

 – Once the door is placed on the hinges, push each 

locking lever up fully to lock the door onto the hinge.

 

˜

OB60SD models

 – Ensure the door is firmly in place on the hinges. 

Open the door completely again and push each locking lever down 
fully to lock the door onto the hinge.

3 

IMPORTANT!

Ensure the levers are both fully locked before trying 
to shut the door.

OB60 models

OB60SD models

OB60 models

OB60SD models

Summary of Contents for OB60 Series













Reviews:

No comments