background image

-  4  -

NOTE.  There is still power to the components
when the POWER button in the “off” state.
Always unplug the power cord before
commencing service work or disassembly.

2.

To remove the lid, open it to the upright

position and lift it clear.

3.

Remove 2 screws from the rear of the

console.  The console can be removed to gain
access to the Motor Controller Module, Display
Module and wiring.

NOTE:  Modules removed from the machine for
return must be protected from electrostatic damage
while in transit by using the special

 package in

which the spare parts were received.

Removing Top Deck

4.

Disconnect Display Module, Motor/Pump,

Rotor Position Sensor harnesses, pressure tube
and diverter valve wiring assembly.  Unclamp
Power Cord by removing the 2 screws holding the
cord clamp and remove ground wire and power
cord plug through the clamp opening.

5.

Remove two rubber buffers and screws from

the front of the top deck.

Removing the Basket

6.

Unclip the bias spring from the front left

suspension rod.  Unclip the neck ring from the top
of the tub.

7.

Remove the fabric softener dispenser,

unscrew the agitator retaining nut and remove the
agitator.

8.

The basket may now be lifted clear.  If the

basket is not easy to lift clear, then remove the
three-spline retaining screws and remove the
driven spline off the shaft and lift out.

Diverter Valve

9.

If the valve is replaced, ensure that a hose

clip is refitted to secure the hose to the tub.

Specifications are subject to change without notice.

After Reassembly and Testing…

If the machine is advanced to either rinse or spin
whilst filling or re-circulating, it may take up to 3
minutes before the drain pump turns on.  This time
allows the diverter valve to cool down and direct
the water flow to the drain hose.

If further help is needed

concerning this appliance

in USA or Canada call:

TOLL FREE 1 888 9 FNP USA

(1 888 936 7872)

Or write to:

Fisher & Paykel Appliances Inc.

27 Hubble

Irvine, CA 92618

 P/N   420600

Summary of Contents for Ecosmart Intuitive Eco GWL11

Page 1: ...A TERRE selon les normes internationales et peuvent présenter un risque d électrocution durant l entretien Le personnel d entretien ne doit pas toucher les pièces suivantes lorsque l appareil est branché les supports d électrovanne et le support de montage de la pompe Pour réduire le risque d électrocution le cordon d alimentation doit être débranché avant tout entretien de l appareil ATTENTION TO...

Page 2: ...kink in the hose 4 Inlet hoses connected to the wrong faucets 5 Cold water exceeds recommended limits 6 The flow rate of water may be too slow No Faucets IWL12 I am not getting any WATER GWL11 Cold and Hot LEDs flashing 1 The faucets haven t been turned on 2 Inlet hose screens may be blocked 3 The hoses may be kinked 4 The drain hose is too low or the drain hose is pushed into the standpipe too fa...

Page 3: ...or Fault code 37 Machine has not drained out Check that the pump is not blocked or that the drain hose outlet is not crushed or blocked or drain hose outlet is too high Maximum is 7 ft Pressure Tube Fault Fault code 39 The probable cause of this fault is that the pressure tube has become blocked crushed or has fallen off Basket Disengage Fault Fault codes 40 47 The floating basket has not engaged ...

Page 4: ...nd screws from the front of the top deck Removing the Basket 6 Unclip the bias spring from the front left suspension rod Unclip the neck ring from the top of the tub 7 Remove the fabric softener dispenser unscrew the agitator retaining nut and remove the agitator 8 The basket may now be lifted clear If the basket is not easy to lift clear then remove the three spline retaining screws and remove th...

Reviews: