There will be a distinctive smell and a small amount of smoke during the conditioning process as manufacturing residue is burnt off.
This is normal, but make sure the kitchen is well ventilated during the conditioning.
Once cooled, wipe out the oven with a damp cloth and mild detergent, and dry thoroughly.
It is important to condition your oven before using it for cooking and baking. Conditioning will burn off any manufacturing residues and ensure
that you get the best results right from the start.
1
Make sure you have removed ALL the cable ties used to secure the shelving during transit.
2
Make sure you have set the clock.
3
Make sure all the shelves are fitted.
USING THE TIMER
FOR MORE INFO
FIRST USE
7 CONDITION THE OVEN
7 CONDITION THE OVEN
4 FIT BOTH CATALYTIC PANELS
5 REPLACE BOTH SIDE RACKS
6 REPLACE SHELVING
Catalytic panel
Stop Notch
Guard rail
Guard
rail
Front bar
Rear shelf tag
Front shelf tag
To replace a wire shelf
, check the guard rail (as shown) to make sure the shelf is the right way up. slide it horizontally back along the side racks
ensuring it is level and the stop notch is facing down.
To replace a telescopic sliding shelf,
position it so that the front bar is toward you, as shown.
Check that the sliding frame is not extended.
Check the guard rail (as shown) to make sure the shelf is the right way up.
Position the shelf so that it is level and the rear shelf tag at the back of the sliding frame rests behind the side rack wire (as shown).
Then push the sliding shelf all the way to the back of the oven, until the front shelf tag drops into place behind the side rack wire.
For your safety, the wire shelves and telescopic sliding frames are built together as one unit and are not separable. This means that when placed
properly on the side racks, the slides will prevent the wire shelves from tilting when pulled towards you.
To prevent the tags from lifting off the side racks, take care to slide the shelves forward horizontally.
Place each catalytic panel flush against the side wall, noting
the position of the cutouts for the lamp and lock nuts
To replace the side racks
, locate the top of the side rack into the
two upper lock studs and gently push the retaining wire back
under the lower lock stud.
N
O
I
T
C
N
U
F
E
R
U
T
A
R
E
P
M
E
T
1
1
2
Replacing a wire shelf
Replacing a telescopic sliding shelf
retaining wire
lock stud
7
Leave the temperature at 200
o
C
for 5 minutes.
The halo will remain white.
1
Select the timer
by pressing
the right scroll
button once.
The timer
indicator will appear
and the colon will flash.
2
Press the select
button to
confirm.
The display will flash to indicate
the timer is ready to be set.
3
Set the time by pressing the
scroll
buttons.
Holding the buttons down
will speed up the scrolling.
4
Press the select
button to
confirm.
The timer will then begin to
count down.
If you want to check the time
of day, press the cancel
button once.
Press the right scroll
button
to scroll back to the timer.
8
When you have finished, turn the function dial to
Off
. The halos will go out.
You can use the timer at any time, even if you are not using the oven.
If the time is more than an hour, the display will count down in minutes (hr:min). If it is less than an hour, it will count down in seconds (min:sec).
You can set the timer for up to 23 hours 59 minutes.
Important!
The timer does NOT turn the oven off.
To modify the timer setting
1
Make sure the display shows the remaining time counting down.
2
Press the select
button.
3
Press the scroll
buttons to set a new time.
4
Press the select
button to confirm.
To cancel the timer setting
1
Make sure the display shows the remaining time counting down.
2
Press the cancel
button until the display shows the time of day and the timer
indicator disappears.
When the set time is up
The display will show
0
:
00
and a tone will sound every 15 seconds.
Press any button to stop the tone sounding. The display will revert to showing the time of day.
For detailed information on the
other features of your oven
For warranty information
If you…
have any questions or comments
need a Fisher & Paykel authorized
technician to service your product
need replacement parts or accessories
want to register your product
see your ‘User guide’
see your ‘Service and warranty’ booklet
see your ‘Service and warranty’ booklet or contact us
590479A 12.12
N
O
I
T
C
N
U
F
N
O
I
T
C
N
U
F
E
R
U
T
A
R
E
P
M
E
T
E
R
U
T
A
R
E
P
M
E
T
4
Select the
Bake
function.
The halo will glow white.
Each function has a preset
temperature and so the oven
will start heating at the
Bake
preset temperature of 180
o
C.
5
Set the temperature to 200
o
C for 30 minutes.
While the oven is heating up, the temperature halo
will glow red and the temperature indicator will
alternately show the actual and set temperatures.
When the oven has reached set temperature, a tone
will sound and the halo will turn white.
6
After 30 minutes is up,
select
the
Fan Grill
function.
NZ
toll-free, 24/7
0800 372 273
AU
toll-free, 24/7
1300 650 590
GB
toll-free, 24/7
0845 066 2200
IE
toll-free, 24/7
1800 625 174
www.fisherpaykel.com