manualshive.com logo in svg

Fisher & Paykel 525911L, Use & Care Manual

Share
Download
Fisher & Paykel 525911L Use & Care Manual Download Page 10

9

Lock

The Lock function disables all the other functions on the

DishDrawer. This function is useful when cleaning the

control panel and can also prevent children from turning

the DishDrawer on or off accidentally. This button can be

used when the DishDrawer is in operation and will remain

active until the Lock is deactivated.

To activate this function, press and hold the 

Lock

 button

until the “key” symbol at the bottom of the Electronic

Display appears continuously and is no longer blinking.

All the other buttons are now inactive.

To deactivate this function, press and hold the 

Lock

 button

until the

 

“key”

 

 symbol in the Electronic Display

disappears.

Figure  2  - Electronic

Display showing the lock

mode

Start / Pause

This button has a number of functions.  It serves to:

·

Start the DishDrawer, once the desired wash program has been selected.

·

Interrupt the wash program while in operation.

When pausing the  DishDrawer, wait until you have heard two additional

beeps before you open the drawer, allowing the lid seal to deflate.

While in the pause mode, the electronic display will be green, the “min”

symbol will flash and the "smiley face" symbol will disappear.

·

Restart the DishDrawer after being paused.

You may notice a delay after the

 Start / Pause

 has been pressed.  During this

time the lid seal will be inflating.

·

One Button Start.

This starts the DishDrawer and will run the last  wash program used,

excluding Delay Start if used in the previous wash.

·

Initiates the Delay Start.

NOTE:

Under no circumstances do we recommend that you open the DishDrawer while in

operation unless you have pressed the 

Start / Pause 

button.

 If the drawer is opened

during the wash program, there is a possibility of getting wet, burnt, or damaging the

DishDrawer.  There are safety mechanisms in place to stop the DishDrawer if it is

opened.

If  Fault Code “U2” Appears:

The fault code 

“U2”

 will be displayed if the drawer is opened during operation.  To

remove this fault code, press

 Power

.   Ensure the drawer is closed.  The DishDrawer

will now be ready to start from the beginning of the wash program.  You may have to

add more detergent in the dispenser and then press

 

the

 Start / Pause

 button to start the

DishDrawer. The DishDrawer will not restart where it was interrupted after a “U2” fault.

All manuals and user guides at all-guides.com

Summary of Contents for 525911L






































Reviews:

No comments

Brands by name

Popular brands

Load more brands