INCOMING
PHONE
LINE
TO
HANDSET
PHONE
LINE
WARNING:
TO PREVENT
RISK OF SHOCK
DISCONNECT
TELEPHONE LINE
AT TELECOM
JACK BEFORE
SERVICING
THIS UNIT.
WEEKLY TESTING IS
REQUIRED TO ENSURE
PROPER OPERATION
OF THIS SYSTEM
ALL OUTPUT CIRCUITS ARE POWER LIMITED.
PREMISES
TELEPHONE
1
2
3
4
8
6
5
11
7
10
12
15
16
13
14
PHONE
FUTURE
USE
FUTURE
USE
SOUNDERS
PLCD
AC
EARTH
GROUND
EARTH
GROUND
INCOMING
TELEPHONE
LINE
RING
TIP
RING
TIP
( )
( )
(+)
(+)
( )
PIEZO
6-14VDC
120mA max.
(e.g. WAVE2EX)
6-14VDC
30mA max.
DATA
OUT
SYNC
IN
PO
WERLINE
CARRIER DEVICES
RJ11
8
POS
JACK
AC
AC
SYNC
COM
DATA
9
BELL
08000-009-V0
NOTE
USE ONLY THE K10145X10
OR K10145CN
TRANSFORMERS PROVIDED
K10145X10
PLUG-IN
TRANSFORMER
9VAC, 25VA
X10
ONLY
CONNECTIONS
GND
D
ATA
I
N
GND
D
A
T
A
OUT
LOCAL SOUNDER DISABLE
SHUNT REMOVE TO DISABLE
STANDARD/HIGH
CAPACITY BATTERY
CONNECTOR
SUPER HIGH CAPACITY
BATTERY CONNECTOR
ALARMNET LRR/IP
COMMUNICATIONS PORT
INTERNAL 7845i-L*
MODULE ONLY
THE READYGUARD-RI CONTROL IS COMPATIBLE
WITH THE FOLLOWING INTEGRAL
RECHARGEABLE BATTERY PACKS:
REPLACE EVERY FOUR YEARS
P/N LYNXRCHKIT-SC
P/N LYNXRCHKIT-HC
P/N LYNXRCHKIT-SHA
* WHEN AVAILBLE
UL NOTE
THE MINIMUM WIRE SIZE USED FOR TELEPHONE
INSTALLATIONS MUST BE #26 GAUGE
ReadyGuard-RI WIRING CONNECTIONS
System Programming
Step
Action
1.
Set a programming default as follows:
a. Enter Programming mode: Installer Code + 8 0 0.
b. Press *97, then press a number 1-4 to select a default table from the tables listed on page 1.
2.
Program the variable data fields as follows:
a. RF House ID - Press *24, then enter the desired 2-digit RF House ID for wireless keypads.
b. PABX Access Code (if used) - Press *40, then enter up to 6 digits. If fewer than 6 digits are used, press [*]
to end the field and advance to the next field.
c. Primary Phone Number - Press *41, then enter the primary phone number, up to 20 digits. If fewer than 20
digits are used, press [*] to end the field and advance to the next field.
d. Secondary Phone Number (if used ) - Press *42, then enter the secondary phone number, up to 24 digits. If
fewer than 24 digits are used, press [*] to end the field and advance to the next field.
e. Secondary Account Number (if used) - Press *44, then enter the secondary account number. If only 3 digits
are used, press [*] to end the field and advance to the next field.
f. Primary Account Number (if used) - Press *43, then enter the primary account number. If only 3 digits are
used, press [*] to end the field and advance to the next field.
g. Pager Characters - Press *88 if using Default Table 4, then enter up to 16 digits which may be required by
your pager service (e.g. account number, PIN, etc.). If fewer than 16 digits are used, press [*] to end the field
and advance to the next field.
h. Download Phone Number - Press *94, then enter the downloading computer phone number, up to 20
digits. If fewer than 20 digits are used, press [*] to end the field.
- 3 -
