Firman WH03344 Operator'S Manual Download Page 16

English                                                                                                                                                  Customer Service: 1-844-FIRMAN1

5. Using oil funnel, slowly pour contents of provided oil bottle into oil fill opening until oil reaches 
upper  limit  "H"  mark  on  the  dipstick.  Be  careful  not  to  overfill.  Overfilling  could  cause  engine 
starting problems or engine damage.

6.Replace oil fill cap/dipstick and fully tighten.

8.Oil level should be checked prior to each use or at least every 8 hours of operation. Keep oil 
level maintained.

7.Reinstall maintenance cover and tighten screws.

The  portable  generator  is  equipped  with  a  low  oil  shutdown.  If  the  oil  level  drops  below  the 
minimum  required  level,  a  sensor  will  activate  an  internal  switch  stopping  the  engine.  If  the 
engine shuts off and the oil level is within specifications, check to see if generator is sitting at an 
angle. Place portable generator on an even surface to correct this. If engine fails to start, the oil 
level may not be high enough to deactivate the internal low oil level switch. Make sure the sump is 
completely full of oil to the upper limit (H). Do not operate engine until oil level issue is corrected. 
Contact Firman customer service.

Low Oil Shutdown

Add Gasoline

WARNING!

 Fuel and its vapors are extremely flammable which could cause burns or fire 

resulting in death or serious injury.

Turn generator engine OFF and let it cool at least 2 minutes before removing fuel cap.
Do Not refuel or move generator when engine is running.
Move generator outdoors prior to adding or draining fuel
Keep fuel away from any ignition sources.
Do not overfill tank, allow space for fuel expansion.
If any fuel spills, wait until it evaporates before starting engine
Check and replace fuel lines, tank, cap, and fittings prior to each use if any damage or leaks 
are found.

Fuel must meet these requirements: 

Clean, fresh, unleaded gasoline with a minimum of 87 octane.
For high altitude use, see Operation at High Altitude.
Gasoline with no more than 10% ethanol is acceptable.

E10

E15

14

OPERATION

Summary of Contents for WH03344

















































Reviews: