Firegear B360EXSSA11-N Installation And Operation Instructions Manual Download Page 1

 

INSTALLATION AND 
OPERATION INSTRUCTIONS 

 

FIREGEAR

 

REVOLUTION EXSS OUTDOOR 

SERIES GAS LOG HEATER & VENTED 

DECORATIVE GAS LOG HEARTH KIT  

 
If for any reason, you cannot follow these instructions, 

FOR 

ANY REASON WHATSOEVER

, just return the product to your 

dealer, and the dealer will refund your money. 

 

“PLEASE”

 do 

not use this product if you cannot follow these instructions. 
 
CONGRATULATIONS, on the purchase of your new 

fire

gear 

REVOLUTION VENTED / UNVENTED GAS LOG HEATER.   
 
 
 
   

GENERAL INFORMATION 

 
These instructions are intended as a general guide and do not 
supersede national or local codes in any way.  State or local 
codes may only allow operation of this appliance in a vented 
configuration.  Check your state or local codes.  Authorities 
having jurisdiction should be consulted before installation. 
 
 

!!! IMPORTANT !!! 

Read these instructions carefully before installing or operating 
this gas appliance.  These instructions should be left with the 
homeowner for future reference. 

INSTALLER:

 Leave this manual with the appliance. 

CONSUMER:

 Retain this manual for future reference. 

 

!!! WARNING !!! 

If the information in this manual is not followed exactly, a fire or 
explosion may result causing property damage, personal injury 
or loss of life. 

 

FOR OUTDOOR USE ONLY 

Listed below are the Canadian Standards Association (CSA) 
certification numbers for the gas and ignition systems used with 
firegear outdoor gas log systems. The valve systems are manufactured 
by Skytech II, Inc. The complete systems are not certified as a whole 
due to the lack of standard for decorative outdoor gas burning 
appliance; no such standard is currently available. 
 

Valve/Ignition System 

 

 

 

AF-1(0,1)(0,1,2,3,4)(0,1, 5)    3/8, 3/8 

Applicable Standards 

 

 

 

ANSI Z21.78-2005-CSA 6.20-2205 

 

Combination Gas Controls For Gas Appliances 
ANSI Z21.78a-2007-CSA 6.20a-2007 
ANSI Z21.78b-2008-CSA 6.20b-2008 

 

 

 

TABLE OF CONTENTS 

 

GENERAL INFORMATION 

 

 

 

MODELS 

 

 

 

 

SHIPPING AND PACKING LIST 

 

 

 

SAFETY INFORMATION   

 

 

 

SPECIFICATIONS  

 

  

 

CLEARANCES 

 

 

 

 

PROVISIONS FOR COMBUSTION & AIR 

 

 

INSTALLATION    

 

 

 

SET-UP & ASSEMBLY  

 

  

 

OPERATION  

 

 

 

             14 

LIGHTING INSTRUCTIONS 

 

             15 

 

MAINTENANCE & SERVICE 

 

             16 

CURING REFRACTORY LOGS 

 

             16 

              

PARTS LISTING   

 

 

             17 

TROUBLE SHOOTING 

 

 

             21 

  

WARRANTY 

 

 

 

             22

 

 
 

 

WHAT TO DO IF YOU SMELL GAS: 

 
<    Do not try to light any appliance. 
 
<    Do not touch any electrical switch; do not use 

any phone in your building. 

 
<    Immediately call your gas supplier from a 

neighbor’s phone.  Follow the gas supplier’s 
instructions. 

 
<    If you can not reach your gas supplier, call the 

fire department. 

 
Do not store combustible materials or use gasoline 
or other flammable vapors and liquids in the vicinity 
of this or any other appliance. 
 
Installation and service must be performed by a:  
Qualified technician, service agency, or the gas 
supplier. 
 
 
 

 

 

 

 

 

 

 
 
 
 

REVEXSS 

– 2.0 

 

Summary of Contents for B360EXSSA11-N





















Reviews: