NEMA 14-50 Receptacle and Plug
—
FireAvert to the smoke detector, the FireAvert con-
stantly monitors the surrounding area for the smoke
detector alarm. The FireAvert has a 10 second - 1 mi-
and disconnects
power to your range and the LED indicator on the
FireAvert turns solid RED.
—
In the event that the FireAvert
ance, you must reset the FireAvert before it can be used
further. To reset the FireAvert, switch OFF the circuit
breaker to the range for 10 seconds, then switch it back
ON again. The reset is successful if power returns to the
Re-Syncing the Unit—
If a new smoke detector or appli-
ance is installed in the home or building where the
FireAvert is located, the FireAvert will need to be reset
and synced with the new smoke detector. First, reset the
FireAvert and enter sync mode by pushing the reset button,
the LED indicator will start blinking red and the chirping
sounds starts. To synch the FireAvert to the new smoke
detector and/or appliance, follw
Steps 4-8
in the
Installation Instructions.
Issue
LED Indicator won’t
light and/or there is
no chirping sound.
Switch the circuit breaker OFF for 10
seconds, then back ON. Repeat sev-
ing, contact customer support.
step #4, LED indica-
tor is solid GREEN +
no chirping sound.
the LED Indicator blinks RED and
Steps 5-7
in
The FireAvert will
not exit sync mode.
Smoke detector might be too far
from FireAvert. Move smoke detector
tact Support for assistance.
The FireAvert en-
tered
Mode even though
my stove was
switched OFF.
has a fail-
detector sounds for more than ten
minutes, even if the installed appli-
ance is switched OFF.
To switch OFF the “fail-safe” feature,
Reset the FireAvert by switching the
circuit breaker OFF for 10 seconds
and back ON again. The FireAvert
will return to normal mode as indi-
cated by a GREEN LED indicator.
The FireAvert
doesn’t seem to
Mode and switch
OFF the stove or
range reliably.
Ensure you are using an approved
in the smoke detector and move the
smoke detector closer to the appli-
ance where the FireAvert is installed.
Reset and re-sync the FireAvert. If
the issue persists please contact
customer support.
3. Install
the FireAvert. Insert the range plug into the
receptacle on the FireAvert. Line up the plug blades on
the back of the FireAvert with the power outlet on the
wall and use both hands to insert the FireAvert firmly
against the outlet face.
1. Switch OFF
circuit
breaker to the range.
(see Fig. 1.0) Note: Test
your appliance for power
to verify that the correct
breaker has been
switched OFF.
4. Switch ON
circuit breaker to the range.
6. Push
the range back against wall. NOTE: YOU MUST
PUSH THE STOVE BACK AGAINST THE WALL BE FOR
ATTEMPTING TO SYNC THE FIREAVERT. Syncing the
FireAvert with the stove out from the wall will cause the
FireAvert to not properly work with your smoke alarm.
Make sure that you do not pinch or squeeze the FireAvert
between the range and the wall.
Mode as indicated by a solid
GREEN LED Indicator with an inter-
7. Synch
the nearest smoke detector
to the FireAvert by pressing and hold-
ing the “Test”
alarm sounds for approximately 30
seconds. When success- fully
Synched, the LED indicator on the
FireAvert will stay solid GREEN, and
the RED flashing and chirping sound
will stop.
8. Test
for a successful synch
power to your stove. If the synch is successful, the
FireAvert will cut power to the range between 10 sec-
onds and one minute.
Reset
the FireAvert by switching the circuit breaker OFF
for 10 seconds, then back ON again.
5. Prepare
the stove / range for synching by ensuring
that ALL oven and range elements are switched OFF.
NOTE
the range should be ON . Reset clock if needed.
NOTE
: The FireAvert must be correctly Synched to a
smoke detector before use.
.
Mode and cut power to the stove even if the stove is in
Disable “Fail-Safe” Mode by pressing
-safe mode has been
turned o
ff
. To re-enable the fail-safe mode feature,
-safe mode is re-
enabled. FireAvert, LLC encourages you to leave this
2. Move
stove / appliance away from the wall to pro-
vide access to the power outlet and
unplug
the appli-
ance by gently rocking the plug up and down and from
side to side while withdrawing the plug.
Note: This model of FireAvert is designed to be used
with NEMA 14-50 plugs and outlets ONLY.
