Fire-Lite ACM-16ATF Instruction Manual Download Page 39

Page: 39 / 68

AEM-16ATF

5. LED and Switch Functions

ACM-16ATF/ACM-32AF Manual PN 51480:A0 02/02/01

AEM-16ATF

The following is a description of the various LEDs and switches located on
the AEM-16ATF.

Figure 15 AEM-16ATF Series LED & Switch Locations

Lamp Test Switch -

When pressed, it lights all the LEDs (except the On-

line LED) on the expander and sounds the piezo for as long as the switch is
held down.

Inactive LEDs -

These two LEDs are not functional on expander modules.

Point-Active LED -

Flashes to indicate an active point; after being

acknowledged it glows until reset.

Trouble LED -

Flashes to indicate a trouble situation. After being

acknowledged it glows until reset. If communication with control panel is
broken,

all

trouble LEDs flash.

Control Switch -

Functions as a local Lamp Test for the two LEDs

dedicated to this point. Control switches can be used to execute such system
functions as ACKNOWLEDGE, SIGNAL SILENCE, and SYSTEM
RESET. Switches can also be used to control the status of various output
circuits.

M-1

Lamp Test Switch

Inactive LEDs

Point-Active LED

Trouble LED

Control Switch

Summary of Contents for ACM-16ATF





































































Search results

Summary of Contents for ACM-16ATF

Reviews:

Related manuals for ACM-16ATF

Brands by name

Popular brands

Fire-Lite ACM-16ATF, Instruction Manual

Search results

Summary of Contents for ACM-16ATF

Reviews:

Related manuals for ACM-16ATF

Brands by name

Popular brands