background image

LCD-40 Series Annunciators

Features of LCD-40 and LCD-40L

5

Document 50327    Rev D1   1/14/99   P/N 50327:D1

The LCD-40 Series is capable of displaying English-language text of 
system point status including device type, independent point alarm, 
trouble or supervisory, zone and custom alpha labels programmed into 
the control panel.  The LCD-40 Series also provide system status LEDs 
to display Power, Alarm, Trouble and Supervisory conditions.  The 
LCD-40 is capable of performing system acknowledge, silence, drill 
and reset remotely while the LCD-40L does not have these features.

Communication between the control panel and the LCD-40 Series is 
accomplished over a two-wire serial interface employing the EIA-485 
communication standard.  Up to 32 annunciators may be connected to 
the two-wire EIA-485 circuit.  The annunciators may be powered from 
the host FACP or remote UL listed, filtered, power supplies.

1.1

Features of LCD-40 and LCD-40L

• 40-character LCD display (20 characters x 2 lines) is backlit 

under normal and alarm conditions

• System Status LEDs for Power (green), Alarm (red), Trouble 

(yellow) and Supervisory (yellow)

• No programming necessary — duplicates messages at control 

panel display

• Local piezo sounder with alarm and trouble resound
• Device type identifiers from the control panel
• Device & zone custom alpha labels from the control panel
• Time/date and device address from the control panel
• EIA-485 connects to control panel terminal port (requires 

DIM-485 module)

• Plug-in terminal blocks for ease of installation and service
• DIP switches control piezo enable/disable and transmit/receive 

mode

• Up to 32 LCD-40 Series Annunciators per MS-9200
• Mounting options:

Surface mounting in SBB-3 (2.75" depth)

Semi-flush mounting in three-gang electrical box 
(Fire•Lite P/N 10103) with a minimum depth of 2.187"

Can be located up to 3,000 feet (900 m) from the panel

• Backlight turns off during AC loss to conserve battery power but 

will turn back on if an alarm condition occurs.

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Summary of Contents for LCD-40 Series





























Reviews: