Fiplex TXPA220 User & Installation Manual Download Page 6

 

 UM-0918

 

 

 

2

 

FCC Compliance

 

 

 
FCC Part 15.19 Warning Statement  
THIS  DEVICE  COMPLIES WITH  PART  15  OF  THE  FCC  RULES.  OPERATION  IS  SUBJECT 
TO  THE  FOLLOWING  TWO  CONDITIONS:  (1)  THIS  DEVICE  MAY  NOT  CAUSE  HARMFUL 
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, 
INCLUDING 

INTERFERENCE 

THAT 

MAY 

CAUSE 

UNDESIRED 

OPERATION.  

 
FCC Part 15.21 Warning Statement  
NOTE:  THE  GRANTEE  IS  NOT  RESPONSIBLE  FOR  ANY  CHANGES  OR  MODIFICATIONS 
NOT  EXPRESSLY  APPROVED  BY  THE  PARTY  RESPONSIBLE  FOR  COMPLIANCE.  SUCH 
MODIFICATIONS COULD VOID 

THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.  

 
FCC  Part  15.105(b) Warning  Statement  NOTE:  This  equipment  has  been  tested  and  found  to 
comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These 
limits are designed to provide reasonable protection against harmful interference in a residential 
installation. This equipment generates uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful interference  to radio 
communications. However, there is no guarantee that interference will not occur in a particular 
installation.  If  this  equipment  does  cause  harmful  interference  to  radio  or  television  reception, 
which can be determined by turning the equipment off and on, the user is encouraged to try to 
correct  the  interference  by  one  or  more  of  the  following  measures:  -  Reorient  or  relocate  the 
receiving  antenna.  -  Increase  the  separation  between  the  equipment  and  receiver.  -  Connect 
the equipment into an outlet on a circuit different from that to which the receiver is connected. - 
Consult the dealer or an experienced radio/TV technician for help. 
 
 

ATTENTION:  

 

For safety reasons maintain a minimum separation of 114.92 cm from the antenna to 
all persons.  

 
 
 
 
 
 
 

Summary of Contents for TXPA220











Reviews: