Finlux 55-FAE-9060, Owner'S Manual

Page: 38 / 60

English
- 5 -
Stand Installation &
Wall Mounting
Assembling / Removing the pedestal
Preparations
Take out the pedestal(s) and the TV from the packing
case and put the TV onto a work table with the screen
panel down on the clean and soft cloth (blanket, etc.)
‡ 8VHDÀDWDQG¿UPWDEOHELJJHUWKDQWKH79
‡
Do not hold the screen panel part.
‡ Make sure not to scratch or break the TV.
Assembling the pedestal
1.
Place the stand(s) on the stand mounting
pattern(s) on the rear side of the TV.
2.
Insert the screws provided and tighten them gently
XQWLOWKHVWDQGLVSURSHUO\¿WWHG
Removing the pedestal from the TV
Be sure to remove the pedestal in the following way
when using the wall-hanging bracket or repacking
the TV.
‡ Put the TV onto a work table with the screen panel
down on the clean and soft cloth. Leave the stand(s)
protruding over the edge of the surface.
‡ 8QVFUHZWKHVFUHZVWKDW¿[LQJWKHVWDQGV
‡
Remove the stand(s).
When using the wall mount bracket
Your TV is also prepared for a VESA-compliant wall
mount bracket. If it is not supplied with your TV, contact
your local dealer to purchase the recommended wall-
hanging bracket.
Holes and measurements for wall mount bracket
installation;
VESA WALL MOUNT MEASUREMENTS
H e e
Sizes (mm)
W H
200 200
S e Sizes
e ( )
min. (mm) 10
max. (mm) 13
e ( ) M6
Antenna Connection
Connect the aerial or cable TV plug to the AERIAL
INPUT (ANT) socket or satellite plug to the SATELLITE
INPUT (LNB) socket located on the rear side of the TV.
Rear side of the TV
/1%
$17
1.
Satellite
2.
Aerial or cable
If you want to connect a device to the TV, make
VXUHWKDWERWKWKH79DQGWKHGHYLFHDUHWXUQHGRႇ
before making any connection. After the connection
is done, you can turn on the units and use them.
English
- 6 -
Other Connections
,I\RXZDQWWRFRQQHFWDGHYLFHWRWKH79PDNHVXUHWKDWERWKWKH79DQGWKHGHYLFHDUHWXUQHGRႇEHIRUHPDNLQJ
any connection. After the connection is done, you can turn on the units and use them.
Connector Type Cables Device
COMPONENT
Component
Video
Connection
(back) VGA to Component Connection Cable
HDMI
Connection
(back&side)
VGA
Connection
(back)
AUDIO IN
VGA/
Component
Audio
Connection
(back)
Component/VGA
Audio Cable
SPDIF
SPDIF
(Optical Out)
Connection
(back)
COMPOSITE
Composite
(Audio/Video)
Connection
(back)
Audio Video Cable
HEADPHONE
Headphone
Connection
(side)
USB
Connection
(side)
CI
Connection
(side)
CAM
module
LAN
Ethernet
Connection
(back)
LAN / Ethernet Cable
To enable VGA/Component audio,
you will need to use the back audio
inputs with a VGA/Component audio
cable for audio connection. When
using the wall mounting kit (contact
your dealer to purchase one, if not
supplied), we recommend that you
plug all your cables into the back of
the TV before mounting on the wall.
Insert or remove the CI module only
when the TV is SWITCHED OFF. You
should refer to the module instruction
manual for details of the settings. The
USB inputs on the TV support devices
up to 500mA. Connecting devices that
have current value above 500mA may
damage your TV. When connecting
equipment using a HDMI cable to your
79 WR JXDUDQWHH VX௻FLHQW LPPXQLW\
against parasitic frequency radiation
and trouble-free transmission of high
GH¿QLWLRQVLJQDOVVXFKDV.FRQWHQW
you have to use a high speed shielded
(high grade) HDMI cable with ferrites.