manualshive.com logo in svg

Finish Thompson M10X, Operations & Parts Manual

Share
Download
Finish Thompson M10X Operations & Parts Manual Download Page 17

15

Finish Thompson Inc. hereby declares that the following machines fully comply with the applicable 

health and safety requirements as specified by the EU Directives listed. This declaration is valid 

provided that the devices are fully assembled and no modifications are made to these machines.

Type of Device:

Drum or Container Pump

Pump Models:

PFS-27, PFS-40, PFS-48, PFS-60, PFS-72

EU Directives: 

Equipment and protective systems intended for use in potentially 

 

explosive atmospheres (2014/34/EU)

EU-Type Examination:

Physical Technical testing Institute 1026

 

Ostrava-Radvanice 

FTZU 04 ATEX 0293X

Product Quality Assurance Notification:

Physical Technical Testing Institute 1026

 

Ostrava-Radanice

 

FTZU 08 ATEX Q 003

Applicable Harmonized Standards:

EN 1127-1: 2011

EN 13463-1:2009

EN 13463-5:2011

Signed,

Casey D. Bowes

CEO and President

August 1, 2016

EU DECLARATION OF CONFORMITY

Summary of Contents for M10X




















Reviews:

No comments

Brands by name

Popular brands

Load more brands