Finish Thompson DB11 series Assembly, Installation And Operation Manual Download Page 18

Page: 18 / 22

*Cast iron motor adapters have been upgraded to polypropylene effective August 2009. To upgrade, order one of the options in item 8 above. For IEC 80, 90, 100 & 112 B5 frames, you

will also need one of the options in item 10.

DB11/15 Spare Parts List - cont.

Item Qty

Description

DB11

DB15

Pump Material

Polypro

PVDF

Polypro

PVDF

Motor Adapter Kits (includes items 8A - 8E plus hardware)

Standard motor adapter - all frame sizes

107405

107406

107405

107406

Standard motor adapter w/ non-sparking ring - all frame sizes

107407

107408

107407

107408

ATEX motor adapter w/ PVDF motor adapter & non-sparking ring - all frame sizes

N/A

107413

N/A

107413

Note: 182/184TC & all IEC frames MAY need to order motor adapter flange (item 10) and hardware (items 15-17 & 21-23)

Barrier/Clamp O-ring

Buna

107281

FKM

107279

EPDM

107280

Clamp Ring

Painted cast iron (Standard)

107228

107228-1

107228

107228-1

Painted cast iron with non-sparking ring

107321

107321-1

107321

107321-1

Painted cast iron (ATEX)

N/A

107321-1

N/A

107321-1

Stainless steel

108600

Stainless steel with non-sparking ring

108600-1 108600-1 108600-1

108600-1

Stainless steel (ATEX)

N/A

108600-1

N/A

108600-1

Clamp Ring/Motor O-ring

Buna

107282

FKM

107283

EPDM

107284

Motor Adapter Column

Standard

106890

106890-1

106890

106890-1

ATEX

N/A

106890-2

N/A

106890-2

Motor Adapter Column/Motor O-ring (NEMA 56C/143/143/145TC motors only)

Buna

106549

FKM

106374

EPDM

106373

Drive Magnet Assembly with Snap Ring

6-pole 56C frame (includes set screws)

105878

8-pole 56C frame (includes set screws)

105878-1

6-pole 143/145TC frame (includes set screws)

105878-3

8-pole 143/145TC frame (includes set screws)

105878-4

10-pole 182/184TC frame (includes set screws)

105730-9

6-pole 80 frame

105882

8-pole 80 frame

105882-1

6-pole 90 frame

105882-3

8-pole 90 frame

105882-4

10-pole 100/112 frame

105730-18

Set Screws

NEMA motor frames only

J101084

Snap Ring

56C frame

105708

143/145TC frame

105709

182/184TC frame

105710

80 frame

105711

90 frame

105712

100/112 frame

105710

Summary of Contents for DB11 series























Search results

Summary of Contents for DB11 series

Reviews:

Related manuals for DB11 series

Brands by name

Popular brands

Finish Thompson DB11 series, Assembly, Installation And Operation Manual

Search results

Summary of Contents for DB11 series

Reviews:

Related manuals for DB11 series

Brands by name

Popular brands