Fimap MxL 65 Bt Pro Use And Maintenance Manual Download Page 17

FILLING THE DETERGENT CANISTER (VERSIONS WITH FSS)

After filling the solution tank with clean water, you must fill the detergent canister. Before filling the canister, carry out the following steps:

1. 

Take the machine to the usual place for filling the solution tank.

2.  Perform the procedure for securing the machine ( see the section titled “

SECURING THE MACHINE

”).

3.  Grip the handle (3) on the right-hand side of the recovery tank (

Fig.3

) and turn the tank as far as it will go, until it reaches the maintenance 

position.

4.  Disconnect the male insert (33) from the female insert (34) in the cap (35) of the detergent canister (36) (

Fig.27

).

ATTENTION:

 before pulling on the male insert, push the lever on the female insert.

5.  Gripping the handle (37) on the detergent canister (36), remove the canister from the compartment in the solution tank (

Fig.28

).

6.  Remove the cap (35) from the detergent canister (

Fig.29

).

7.  Fill the canister with the required detergent, as indicated on the label supplied with the machine.

CAUTION:

 protective gloves should always be worn before handling detergents or acidic or alkaline solutions, to avoid serious injury to the 

hands.

WARNING:

 always use low-foam detergent. To avoid the production of foam, put a minimum quantity of anti-foam liquid in the recovery 

tank before starting to clean. Do not use pure acids.

WARNING:

 Always use detergents which have a manufacturer's label that indicates that they are suitable for use with floor scrubbing 

machines. Do not use acid or alkaline products or solvents without this indication.

ATTENTION:

 the dosing system is suitable for frequent maintenance cleaning. Acid or alkaline maintenance detergent tank be used with 

pH values between 4 and 10 and that do not contain: oxidising agents, chlorine or bromine, formaldehyde, mineral solvents. The 

detergents used must be suitable for use with scrubbing machines. Wash the circuit with water after use if the system is not used daily. 

The system can be excluded. In case of sporadic use of detergents with pH between 1-3 or 11-14, use the floor scrubbing machine in the 

traditional way by adding the detergent in the clean water tank and excluding the dosing circuit.

8. 

Ensure that you tighten the cap (35) properly to avoid any leakage of liquid while working. Make sure the detergent suction filter (38) is 

correctly positioned on the bottom of the canister (

Fig.30

).

9.  Grip the canister handle (37) to replace the canister (36) in its compartment inside the solution tank.

10. Connect the male insert (33) to the female insert (34) in the cap (35) of the detergent canister (36).

11.  Grip the handle (3) on the right-hand side of the recovery tank and turn the tank as far as it will go, until it reaches the work position.

CAUTION:

 always use low-foam detergent. To avoid the production of foam, put a minimum quantity of anti-foam liquid in the recovery 

tank before starting to clean. Do not use pure acids.

N.B.:

 to make it easier to measure the detergent on the cap/measuring device, there are notches indicating the detergent percentage 

quantities that can be used. The notches range from a minimum of 0.1% to a maximum of 0.5%.

17

Summary of Contents for MxL 65 Bt Pro





































Reviews: