Fimap MAXIMA BASE BT 2017, Use And Maintenance Manual

Page: 15 / 28

WARNING : before inserting the connector (3) in the socket (4), make sure there is no
condensation or any other type of liquid.
NB : the battery charger power cable is delivered inside the bag containing this instruction
booklet.
6. Plug the battery charger cable into the mains socket.
CAUTION : keep the recovery tank open for the duration of the battery recharging cycle, to
allow gas fumes to escape.
NB : before connecting the battery charger to the mains socket, make sure the characteristics
of the mains supply correspond to those required by the battery charger. Read the battery
charger use and maintenance manual (included in the bag that contains this instruction
booklet).
7. When the recharge cycle is complete, disconnect the battery charger cable from the mains.
8. Disconnect the battery charger power cable from the socket on the battery charger itself.
9. Replace the cap (2) on the battery charger plug.
10. Grip the handle (1) on the right-hand side of the recovery tank and turn the tank as far as it will
go, until it reaches the maintenance position.
ASSEMBLING THE BRUSH (50BT VERSIONS)
ASSEMBLING THE BRUSH (60BT VERSIONS)
For packaging reasons, the brush is supplied disassembled from the machine. To assemble it on the
brush head body, proceed as follows:
1. Make sure the machine is in a safe condition (see “ MACHINE SAFETY MEASURES ”).
CAUTION: users are advised to always wear protective gloves, to avoid the risk of serious
injury to hands.
2. Raise the brush head body and fully depress the "BRUSH HEAD CONTROL" pedal (1) at the
rear of the machine ( Fig.1 ).
NB : to lock the brush head in the raised position, depress the pedal (1) fully and then move it
towards the right-hand side of the machine (
Fig.6
).
3. With the brush head up, insert the brush in the plate housing underneath the brush head, turning
it until the three buttons engage with the notches on the plate itself ( Fig.2 ).
4. Turn until the pin is pushed towards the coupling spring and is locked into place.
For packaging reasons, the brushes are supplied disassembled from the machine. To assemble them
on the brush head body, proceed as follows:
1. Make sure the machine is in a safe condition (see “ MACHINE SAFETY MEASURES ”).
CAUTION: users are advised to always wear protective gloves, to avoid the risk of serious
injury to hands.
2. Raise the brush head body and fully depress the "BRUSH HEAD CONTROL" pedal (1) at the
rear of the machine ( Fig.1 ).
NB : to lock the brush head in the raised position, depress the pedal (1) fully and then move it
towards the right-hand side of the machine ( Fig.6 ).
3. With the brush head in the raised position, press the brush-holder plate retainer (2) and
simultaneously rotate the brush in the direction shown in the image ( Fig.2 ).
ATTENTION : Fig.2 shows the rotation direction of the left-hand brush, rotate in the opposite
direction for the right-hand brush.
4. When brush rotation is prevented, turn until the button on the brush is engaged in the coupling
spring on the brush-holder plate.
5. Repeat the operations completed for the right-hand front brush as well.
NB : carefully read the use and maintenance instructions of the battery charger used.
4. Go to the back of the machine and remove the cap (2) from the battery charger socket ( Fig.2 ).
5. Connect the battery charger power cable connector (3) to the battery charger socket (4) ( Fig.3 ).
CAUTION : before connecting the batteries to the battery charger, make sure it is suitable for
the batteries used.
ASSEMBLING THE ABRASIVE PAD (50BTO VERSIONS)
For packaging reasons, the abrasive pad comes disassembled from the machine. To assemble it on
the brush head body, proceed as follows:
1. Make sure the machine is in a safe condition (see “ MACHINE SAFETY MEASURES ”).
CAUTION: users are advised to always wear protective gloves, to avoid the risk of serious
injury to hands.
2. Raise the brush head body and fully depress the "BRUSH HEAD CONTROL" pedal (1) at the
rear of the machine ( Fig.16 ).
NB : to lock the brush head in the raised position, depress the pedal (6) fully and then move it
towards the right-hand side of the machine ( Fig.1 ).
3. With the brush head in the raised position, slide the abrasive pad into the housing under the
brush head, pressing it until it is firmly attached to it ( Fig.2 ).
ASSEMBLING THE CYLINDRICAL BRUSHES (50BTS VERSIONS)
For packaging reasons, the brushes are supplied disassembled from the machine. To assemble them
on the brush head body, proceed as follows:
1. Make sure the machine is in a safe condition (see “ MACHINE SAFETY MEASURES ”).
CAUTION: users are advised to always wear protective gloves, to avoid the risk of serious
injury to hands.
2. Raise the brush head body and detach the "BRUSH HEAD CONTROL" pedal (1) at the rear of
the machine from the plate retainer ( Fig.1 ).
3. With the brush head raised from the floor, turn the knobs (2) that hold the left lateral carter (3) in
place anti-clockwise ( Fig.2 ).
4. Remove the left lateral carter (3) ( Fig.3 ).
5. Insert the brush into the tunnel ( Fig.4 ), taking care to make sure that the gearmotor's drive shaft
enters the slit in the brush itself.
6. Repeat the previously described operations for the right-hand side as well.
N.B. : In order to be installed correctly, the brushes must form an X when viewed from above in
the forward direction of movement ( Fig.5 ).
ASSEMBLING THE SQUEEGEE BODY
For packaging reasons, the squeegee body comes disassembled from the machine. To assemble it
on the squeegee support, proceed as follows:
1. Make sure the machine is in a safe condition (see “ MACHINE SAFETY MEASURES ”).
2. Raise the squeegee body and turn the squeegee control lever (1) in the direction of the arrow
( Fig.1 ). The lever is located on the back of the machine.
CAUTION : these operations must be carried out using protective gloves to avoid any possible
contact with the edges or tips of metal objects.
3. Unscrew the knobs (2) in the squeegee body pre-assembly ( Fig.2 ).
4. First of all, insert the left-hand pin (3) on the squeegee body in the left slit (4) in the squeegee
support ( Fig.3 ), so that the bushing (5) adheres to the walls of the slit.
5. Repeat the same operation for the right pin.
15
2 3 1
1
2 4
3
1
2
1
1
1
2
2
1
1
2
1 2 3
1
2
3
4 5