Fieldmann FDAN 12001 Instruction Manual Download Page 5

 

5

OPERATING INSTRUCTIONS

BATTERY CHARGER

EN

General safety instructions | 

Preparing to charger

Screw of Protective Cover
Washer
Grindstone
Tightening Female Screw
Tightening Spanner

P

ersonal Precautions

Consider have some one close enough by to come to your aid when you work near

a lead-acid battery.

Have plenty of fresh water and soap nearby in case battery acid contacts skin,

clothing or eyes.

Wear complete eye protection and clothing protection. Avoid touching eyes while

working near battery.

If battery acid contacts skin or clothing, wash immediately with soap and water.

If acid enters eye, immediately flood eye with running cold water for at least 10 

minutes and get medical attention immediately.

NEVER smoke or allow a spark or flame in vicinity of battery or engine.

Be extra cautious to reduce risk of dropping a metal tool onto battery. It might spark

or short-circuit battery or other electrical part that may cause explosion.

Remove personal metal items such as rings, bracelets, necklaces, and watches

when working with lead-acid battery. A lead-acid battery can produce a short-cir-

cuit current high enough to weld a ring or the like to metal, causing a severe burn.

Use charger for charging a LEAD-ACID battery only. It is not intended to supply

power to a low voltage electrical system other than in a starter-motor application.

Do not use battery charger for charging dry-cell batteries that are commonly used

with home appliances. These batteries may burst and cause injury to persons and 

damage to property.

Never charge a frozen battery.

2. P

REPARING TO CHARGER

If necessary to remove battery from vehicle to charge,always remove 

grounded terminal from battery first.Make sure all accessories in the vehicle 
are off,so as not to cause an arc. 

Be sure area around battery is well ventilated while battery is being charged. 

Clean battery terminals. Be careful to keep corrosion from coming in contact 

with eyes.

Add distilled water in each cell until battery acid reaches level specified by 

battery manufacturer.Do not overfill.For a battery without removable cell 

caps,such as valve regulated lead acid batteries, carefully follow 

manufacturer’s recharging instruction.

Study all battery manufacturer’s specific precautions while charging and 

recommended tares of charge.

Determine voltage of battery by referring to car owner’s manual and make 

sure that the output voltage selector switch is set at correct voltage.If 

charger has adjustable charge rate,charge battery initially at lowest rate.

Summary of Contents for FDAN 12001












Reviews: