Field Controls UV-AIRE UV-E Instruction Manual Download Page 8

Phone: 252.522.3031 • Fax: 252.522.0214

www.fieldcontrols.com

© Field Controls, LLC  

P/N 46427300 Rev E 08/09

The health aspects associated with the use of these products and their ability to aid in disinfecting of environmental air have 
not been investigated by UL.

LIMITED WARRANTY

Field Controls, LLC (“Company”) warrants that its products shall be free from defects in material and workmanship 

under normal use for the limited period indicated, 

from the date of manufacture, subject to the provisions 1-8 below.

 

 

Eighteen (18) months

 

All Field Controls Products (except for those listed below as 5 years or 90 days).

 

 

Five (5) years

 

Field Controls Direct Vent Systems (FDVS), Field Oil Vent Kits (FOVP), and ComboVents (CV).

Field Controls warrants that the products listed below shall be free from defects in material and workmanship under 

normal use for the limited period indicated, 

from the date of purchase by the consumer, subject to the provisions 

1-8 below.

 

Ninety (90) days

 

UV lamps/bulbs

 

Provisions:

1. During the limited warranty period, Company, or its authorized service representative, will repair or replace, at Company’s  

  option, without charge, a defective Product.  Product that is repaired may be repaired with new or refurbished replacement  

  parts. Product that is replaced may be replaced with a new or refurbished product of the same or similar design. Company 

  will return repaired or replacement Product to customer in working condition. Labor charges are not covered as part of the  

  limited warranty.
2. With regard to UV lamps/bulbs, customer shall be required to include a "valid proof of purchase" (sales receipt) identifying  

  the Product purchased (Product model or accurate date code information) and the date the Product(s) was purchased. 
3. Product whose warranty/quality stickers, Product serial number plates or electronic serial numbers have been removed,   

  altered or rendered illegible shall not be covered under the limited warranty. 
4. Defective Product must be returned to Company, postage prepaid.
5. IN NO EVENT SHALL COMPANY BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR SIMILAR  

  DAMAGES (INCLUDING, BUT NOT LIMITED TO, LOST PROFITS OR REVENUE, INABILITY TO USE PRODUCT, OR OTHER  

  ASSOCIATED EQUIPMENT, THE COST OF SUBSTITUTE EQUIPMENT, AND CLAIMS BY THIRD PARTIES) RESULTING FROM  

  THE USE OF PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the  

  above limitation or exclusion may not apply to you. 
6. THIS WARRANTY AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, REMEDIES AND  

 

  CONDITIONS, WHETHER ORAL, WRITTEN, EXPRESS, STATUTORY OR IMPLIED.  TO THE EXTENT PERMITTED BY LAW,  

  COMPANY DISCLAIMS ALL IMPLIED AND STATUTORY WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY  

  AND FITNESS FOR A PARTICULAR PURPOSE.  
7. Company makes no warranty of any kind in regard to other manufacturer’s products distributed by Company. Company will  

  pass on all warranties made by the manufacturer and where possible, will expedite the claim on behalf of the customer, but  

  ultimately, responsibility for disposition of the warranty claim lies with the manufacturer.
8. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation or application,  

  abnormal operation or handling, neglect, fire, water or other liquid intrusion are not covered by the warranty.

Summary of Contents for UV-AIRE UV-E









Reviews: