background image

www.fieldcontrols.com

Please retain these instructions after installation.

This device 

MUST

 be installed by a qualified agency in accordance with the manufacturer's installation instructions. The definition of 

a qualified agency is: any individual, firm, corporation or company which either in person or through a representative is engaged 

in, and is responsible for, the installation and operation of HVAC appliances, who is experienced in such work, familiar with all the 

precautions required, and has complied with all the requirements of the authority having jurisdiction.

This product is not sold as a medical device and is not for the purpose of diagnosis of any disease or condition nor for 

use in the mitigation, treatment, or prevention of any disease or condition.

READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE PROCEEDING WITH THE INSTALLATION.

Installation Date:

Installed By:

Phone:

UV-AIRE

® 

AIR PURIFYING SYSTEM

Model: UV-12C, 18C, 28C, 28, 12HP, 18HP, 28HP, 12HPC, 18HPC, 28HPC

*Exclusive 5 position lamp mounting feature!

ITEMS INCLUDED IN KIT:

1- UV-Aire power unit

4- Sheet metal mounting screws

1- Angled mounting bracket

1- Flat mounting bracket

1- Duct board mounting bracket

1- Ultra Violet Lamp

1- Instruction Sheet

1- Wing nut

Caution Labels

Gasket

WARNING:

 DO NOT mount this unit outdoors.

  • This product is designed for indoor installation only (i.e. attics, crawl spaces, basements, etc.).

WARNING:

 UV light will break down plastic materials not rated for UV exposure:

    (Examples: wire insulation, flex duct, drain pans and humidifiers)

 

• The unit must be mounted at least 30” from the above stated type of materials.

 

• If it is necessary to mount the unit in direct line of sight of these types of materials, they must be    

     shielded with aluminum foil, aluminum foil tape, or sheet metal.

SAFETY CONSIDERATIONS

WARNING:

  Never expose eyes or skin to UV-C light from any source.

  • Looking directly at the UV-C light may cause permanent eye damage or blindness. 

  • Never operate the UV-Aire Air Purifying System out of the plenum.

 

• Designed for a closed duct system. Do not mount near a return air opening

 

• All duct openings in direct line of site of the UV light must be sealed with duct tape or equivalent   

     sealing methods.

UV-C light inhibits the growth and reproduction of germs and bacteria that circulate through a home’s 

heating and air conditioning system. The treatment is a safe, silent, and proven way to make your home a 

healthier place to live.

Summary of Contents for UV-AIRE UV-12C













Reviews: