background image

UV-AIRE™ AIR PURIFYING SYSTEM  

Model:

 UV-12C,18C,28C,28,12HP,18HP,28HP,12HPC,18HPC,28HPC 

READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE PROCEEDING WITH THE INSTALLATION 

LEAVE THE INSTALLATION INSTRUCTIONS WITH THE OWNER/OPERATOR OF THE DEVICE 

AFTER OPENING THE CARTON, UNPACK AND INSPECT THE UNIT AND LAMP FOR DAMAGE. 

DO NOT 

INSTALL THIS UNIT IF ANY DAMAGE IS NOTICEABLE.

 

 

SAFETY CONSIDERATIONS 

WARNING:

  

Never expose eyes or skin to UVC light from any source. 

• 

Looking directly at the UVC light may cause permanent eye damage or blindness.  

• 

Never operate the UV-Aire™ Air Purifying System out of the plenum

• 

Designed for a closed duct system. Do not mount near a supply or a return air opening 

• 

All duct openings in direct line of site of the UV light must be sealed with aluminum tape or equivalent 
sealing methods. 

WARNING:

 UV light will break down plastic materials not rated for UV exposure: 

(Examples: wire insulation, flex duct, drain pans and humidifiers) 

• 

The unit must be mounted at least 30” from the above stated type of materials.

 

• 

If it is necessary to mount the unit in direct line of site of these types of materials, they must be shielded 
with aluminum foil, aluminum foil tape, or sheet metal.

 

WARNING:

  DO NOT mount this unit outdoors. 

• 

This product is designed for indoor installation only (i.e. attics, crawl spaces, basements, etc.). 

 

 

 

ITEMS INCLUDED IN KIT: 

1-UV-Aire

 power unit  

4-Sheet metal mounting screws 
1-Angled mounting bracket  
1-Flat mounting bracket 
1-Duct board mounting bracket

 

1-Ultra Violet lamp 
1-Instruction Sheet 
1-Wing nut 
Caution Labels 
Gasket 

UV-C light inhibits the growth and reproduction of germs and bacteria that circulate through a 
homes’ heating and air conditioning system.  The treatment is a safe, silent, and proven way 
to make your home a healthier place to live. 

*Exclusive 5 position lamp mounting feature! 

Summary of Contents for 46453400













Reviews: