background image

S708V & S7708V Instruction Manual

This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used properly in strict accordance
with the instructions contained herein, may cause interference to
radio communication. It has been tested and found to comply with
the limits for Class A computing devices in accordance with the spec-
ifications found in Subpart J of Part 15 of FCC rules, which are
designed to provide reasonable protection against such interference
when the equipment is operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause
interference, in which case the user will be required to take whatev-
er means may be necessary to correct the interference at his own
expense.

Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.

This apparatus does not exceed the Class A limits for radio noise
emission set out in the Radio Interference Regulation of Industry of
Canada.

Cet appareil numérique de la Classe A respecte toutes les exigences
du Règlement sur le matériel brouilleur du Canada.

Federal Communications Commission

and Industry Canada Radio Frequency

Interference Statements

FCC 

PART 15
COMPLIANT

Summary of Contents for S708V








Reviews: