FIBARO FGBHCD-001 Operating Manual Download Page 7

7

OPERATING THE DEVICE

Menu

 allows to perform different actions. In order to use the menu:

1.  Press and hold the button for 3 seconds.

2.  You should hear a short signal while the LED diode blinks white.
3.  Release the button.
4.  wait for the device to indicate desired menu position with a colour:

•   White

 - confirm the start of the firmware update process

•   Green

 - send the current state of CO Alarm

•   Magenta

 - reset the CO peak value

•   Yellow

 - the device reset

5.  Press the button to confirm selection.

#5: Operating the device

Resetting the accessory to factory defaults: 

Reset procedure allows to restore the accessory back to its factory 

settings including HomeKit pairing. Stored carbon monoxide and  

temperature measurement are not deleted.
1.  Press and hold the button.
2.  Release the button when LED indicator glows white and short 

beep sounds.

3.  Click the button when LED indicator glows yellow.
4.  After few seconds the device will be reset (confirmed by red LED 

indicator and long beep).

Button

NOTE

CO Sensor must be de-

tached from the wall 

and battery level must 

be greater than 30% 

of its full capacity to 

perform the firmware 

update process.

i

Self-test 

allows to check operation of the accessory

.

To start the self-test:

1.  Press and hold the button.
2.  The LED indicator will glow white and you will hear a short beep.
3.  Release the button when you hear the first alarm sequence.
4.  Move away from the accessory to protect your hearing.

CAUTION

The alarm is very loud! 

Only the first alarm se-

quence is quieter.

!

If the self-test procedure does not result in emitting sound 

and red light signal, replace the accessory.

!

Summary of Contents for FGBHCD-001













Reviews: