Parameter No. 14 - Switch type connector, you may choose
between momentary and toggle switches.
Default value: 1
Options for changing the parameter:
0
- momentary switch
1
- toggle switch
Parameter No. 15 - Operation of the Dimmer and Roller Shutter
Controller - enabling this option allows the user to dim
lighting/shut roller by associating Dimmer/Roller Shutter
Controller and holding or double press of double switch (only
mono-stable switch).
Default value: 0
Available configuration parameters:
0
- Dimmer/Roller Shutter Controller control is not active
1
- Dimmer/Roller Shutter Controller control is active
Parameter No. 16 - Saving the state of the device after a power
failure. Fibaro Switch returns to the last position saved before
a power failure.
Default value: 1
Options for changing the parameter 0-1
0
- Fibaro Switch does not save the state after a power failure, it
returns to "off" position
1
- Fibaro Switch saves its state before power failure
Possibility to change the configuration of the following
parameters [30 – 33, 40 - 43].
0
- DEACTIVATION - the device does not respond to alarm data
frames
1
- ALARM RELAY ON - the device turns on after detecting an alarm
2
- ALARM RELAY OFF - the device turns off after detecting an alarm
3
- ALARM FLASHING - the device periodically changes its status to
the opposite, when it detects an alarm within 10 min.
Parameter No. 30 - General Alarm, set for relay no. 1.
Default value: 3[byte] ALARM FLASHING
Parameter No. 40 - General Alarm, set for switch no. 2.
Default value: 3[byte] ALARM FLASHING
• 0 - DEACTIVATION - the device does not respond to alarm data
frames
• 1 - ALARM ON - the device turns on after detecting an alarm
• 2 - ALARM OFF - the device turns off after detecting an alarm
• 3 - ALARM FLASHING - the device periodically changes its status
to the opposite when it detects an alarm (lights on/off alternately)
Fibaro Double Relay Switch has two independent alarm groups (i.e.
each of its channels may respond in an individual way to received
alarm data-frames).
VII Operating Fibaro Switch
Fibaro Switch may be operated using the following control
elements:
− any controller compatible with the system (e.g. Home Center
controller)
− a mobile phone (e.g. iPhone and phones from other manufacturers
with appropriate software)
− tablet (such as iPad)
− PC, using a web browser
− push-buttons connected to inputs S1 and S2
− service button B, located inside the housing (activates learn mode)
The device does not respond to a pre-programmed transmitter:
• Make sure that the maximum range is not exceeded and the signal
path is not obstructed by metal surfaces such as metal cabinets, etc.
• Make sure the device is not in the programming mode, or repeat
the programming process.
• Or repeat the programming process.
VIII Procedures for malfunctions
IX Guarantee
1. The Guarantee is provided by FIBAR GROUP Sp. z o.o.
(hereinafter "Manufacturer"), based in Poznan, ul. Lotnicza 1; 60-421
Poznan, entered in the register of the National Court Register kept
by the District Court in Poznań, VIII Economic Department of the
National Court Register, no. 370151, NIP 7811858097, REGON:
301595664.
2. The Manufacturer is responsible for equipment malfunction
resulting from physical defects (manufacturing or material) of the
Device for 12 months from the date of its purchasing.
3. During the Guarantee period, the Manufacturer shall remove any
defects, free of charge, by repairing or replacing (at the sole
discretion of the Manufacturer) any defective components of the
Device with new or regenerated components, that are free of
defects. When the repair impossible, the Manufacturer reserves the
right to replace the device with a new or regenerated one, which shall
be free of any defects and its condition shall not be worse than the
original device owned by the Customer.
4. In special cases, when the device cannot be replaced with the
device of the same type (e.g. the device is no longer available in the
commercial offer), the Manufacturer may replace it with a different
device having technical parameters similar to the faulty one. Such
activity shall be considered as fulfilling the obligations of the
Manufacturer. The Manufacturer shall not refund money paid for the
device.
5. The holder of a valid guarantee shall submit a guarantee claim
through the guarantee service. Remember: before you submit a
guarantee claim, contact our technical support using telephone or
e-mail. More than 50% of operational problems is resolved remotely,
saving time and money spent to initiating guarantee procedure. If
remote support is insufficient, the Customer shall fill the guarantee
claim form (using our website - www.fibargroup.com) in order to
obtain claim authorization.
When the guarantee claim form is submitted correctly, the Customer
shall receive the claim confirmation with an unique number (Return
Merchandise Authorization -RMA).
6. The claim may be also submitted by telephone. In this case, the
call is recorded and the Customer shall be informed about it by a
consultant before submitting the claim. Immediately after submitting
the claim, the consultant shall provide the Customer with the claim
number (RMA-number).
7. When the guarantee claim form is submitted correctly, a
representative of the Authorised Guarantee Service (hereinafter as
"AGS") shall contact the Customer.
8. Defects revealed within the guarantee period shall be removed
not later than 30 days from the date of delivering the Device to AGS.
The guarantee period shall be extended by the time in which the
Device was kept by AGS.
9. The faulty device shall be provided by the Customer with complete
standard equipment and documents proving its purchase.
10. Parts replaced under the guarantee are the property of the
Manufacturer. The guarantee for all parts replaced in the guarantee
process shall be equal to the guarantee period of the original device.
The guarantee period of the replaced part shall not be extended.
11. Costs of delivering the faulty device shall be borne by the
Customer. For unjustified service calls, the Service may charge the
Customer with travel expenses and handling costs related to the
case.
12. AGS shall not accept a complaint claim only when:
• the Device was misused or the manual was not observed,
• the Device was provided by the Customer incomplete, without
accessories or nameplate,
• it was determined that the fault was caused by other reasons than
a material or manufacturing defect of the Device
• the guarantee document is not valid or there is no proof of
purchase,
13. The Manufacturer shall not be liable for damages to property
caused by defective device. The Manufacturer shall not be liable for
indirect, incidental, special, consequential or punitive damages, or
for any damages, including, inter alia, loss of profits, savings, data,
loss of benefits, claims by third parties and any property damage or
personal injuries arising from or related to the use of the Device.
14. The guarantee shall not cover:
• mechanical damages (cracks, fractures, cuts, abrasions, physical
deformations caused by impact, falling or dropping the device or
other object, improper use or not observing the operating manual);
• damages resulting from external causes, e.g.: flood, storm, fire,
lightning, natural disasters, earthquakes, war, civil disturbance, force
majeure, unforeseen accidents, theft, water damage, liquid leakage,
battery spill, weather conditions, sunlight, sand, moisture, high or low
temperature, air pollution;
• damages caused by malfunctioning software, attack of a computer
virus, or by failure to update the software as recommended by the
Manufacturer;
• damages resulting from: surges in the power and/or telecommuni-
cation network, improper connection to the grid in a manner
inconsistent with the operating manual, or from connecting other
devices not recommended by the Manufacturer.
• damages caused by operating or storing the device in extremely
adverse conditions, i.e. high humidity, dust, too low (freezing) or too
high ambient temperature. Detailed permissible conditions for
operating the Device are defined in the operating manual;
• damages caused by using accessories not recommended by the
Manufacturer
• damages caused by faulty electrical installation of the Customer,
including the use of incorrect fuses;
• damages caused by Customer's failure to provide maintenance and
servicing activities defined in the operating manual;
• damages resulting from the use of spurious spare parts or
accessories improper for given model, repairing and introducing
alterations by unauthorized persons;
• defects caused by operating faulty Device or accessories.
15. The scope of the guarantee repairs shall not include periodic
maintenance and inspections, in particular cleaning, adjustments,
operational checks, correction of errors or parameter programming
and other activities that should be performed by the user (Buyer).
The guarantee shall not cover natural wear and tear of the Device
and its components listed in the operating manual and in technical
documentation as such elements have a defined operational life.
16. If a defect is not covered by the guarantee, the Manufacturer
reserves the right to remove such defect at its sole discretion,
repairing the damaged or destroyed parts or providing components
necessary for repair or replacement.
17. This guarantee shall not exclude, limit or suspend the Customer
rights when the provided product is inconsistent with the purchase
agreement.
This Device may be used with all devices
certified with Z-Wave certificate and should be
compatible with such devices produced by
other manufacturers.
Any device compatible with Z-Wave may be added
to Fibaro system.
i
FIBARGROUP
FIBARO
In case of any technical questions contact customer service centre
in your country.
www.fibargroup.com
Parameter No. 31 - Alarm of flooding with water, set for relay
no. 1.
Default value: 2[byte] ALARM RELAY OFF
Parameter No. 41 - Alarm of flooding with water, set for relay
no. 2.
Default value: 2[byte] ALARM RELAY OFF
Parameter No. 32 - Smoke, CO, CO2 Alarm. Set for relay no. 1.
Default value: 3[byte] ALARM FLASHING
Parameter No. 42 - Smoke, CO, CO2 Alarm. Set for relay no. 2.
Default value: 3[byte] ALARM FLASHING
Parameter No. 33 - Temperature Alarm, set for relay no. 1.
Default value: 1[byte] ALARM RELAY ON
Parameter No. 43 - Temperature Alarm, set for relay no. 2.
Default value: 1[byte] ALARM RELAY ON
Parameter No. 39 - Active flashing alarm time.
Default value: 600
Available configuration parameters: [1-65535][ms]
VI Additional Functionality
Operating alarm data frames
Fibaro system allows user to set response of devices to alarm
situations (response to data-frames ALARM_REPORT and
SENSOR_ALARM_REPORT) Fibaro Double Relay Switch responds
to the following types of alarms:
• General Purpose Alarm - GENERAL PURPOSE ALARM [0x00]
• Smoke Alarm - ALARM CO2 [0x02], ALARM CO [0x01], ALARM
SMOKE [0x03]
• Water Flooding Alarm - ALARM WATER [0x05]
• Temperature Alarm - ALARM HEAT [0x04]
Alarm data-frames are sent by devices that are system sensors (e.g.,
flood sensors, smoke detectors, motion detectors, etc.).
The device may respond in the following manner to received
data-frames (settings are configured in configuration parameters,
see section V Configuration ):
