background image

1.3 MULTIJET 16V

(75 & 90 HP)

 

FIAT PUNTO TRAINING OUTLINE 

Fiat Auto S.p.A. 

After Sales Training

 

 

3.10.20 

Cruise Control system check (where available) 

 

Depending on the position of the Cruise Control control lever, the control unit directly controls 

the amount of injected fuel to control and keep the vehicle speed stored in the memory. 

A warning light (actuated by the control unit) on the dashboard indicates the system’s 

operation or deactivation state. 

The Cruise Control is temporarily disabled: 

 

by pressing the brake pedal;  

by pressing the clutch pedal;  

the speed stored in the memory will be resumed by pressing the "Resume" button.  

 

The Cruise Control will not be disabled in case heavy acceleration is requested (e.g. when 

overtaking), and will resume the vehicle’s set speed as soon as the accelerator pedal is 

released. 

The ASR (antispin) function takes priority over the Cruise Control, for safety reasons. 

 

 

 

 

 

 

gb Fiat Grande Punto OK

 

163 / 532

 

© 2004 Fiat Auto S.p.A.  – All rights reserved 

 

Summary of Contents for Punto 2004






















































































































































































































































































































































































































































































































































Reviews: