Fiat Punto 2004 Training Manual Download Page 152

Page: 152 / 533

1.3 MULTIJET 16V

(75 & 90 HP)

FIAT PUNTO TRAINING OUTLINE

Fiat Auto S.p.A.

After Sales Training

3.10.8 Checking the exhaust smoke level during acceleration

In order to reduce the smoke during quick transients, the control unit reduces, depending on

the signals from the accelerator pedal potentiometer, the air flow meter and the engine revs,

the amount of fuel to be injected through:

- pressure regulator (DRV2);

- the injection time of electric injectors (CR1MI2.2).

gb Fiat Grande Punto OK

152 / 532

Summary of Contents for Punto 2004































































































































































































































































































































































































































































































































Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands

Fiat Punto 2004, Training Manual

Search results

Summary of Contents for Punto 2004

Reviews:

Related manuals for Punto 2004

Brands by name

Popular brands