FHP RoutePoint RP-01-00B-C-N-00 Hardware Installation Manual Download Page 13 | Manualshive

Page: 13 / 18

FHP RoutePoint RP-01-00B-C-N-00 Hardware Installation Manual Download Page 13

13

Connecting Power and LAN

Figure 9

SmartPoint and RoutePoint Wireless Router LAN Connection

Step 2

Connect the other end directly into your PC or laptop or to your internal network. See
“Selecting Locations for RoutePoint Gateways and SmartPoint Nodes” on page 5 for
more information on where to connect the SmartPoint or RoutePoint wireless router to
your internal network.

Step 3

If you are not using the Power Over Ethernet option, connect the supplied AC/DC adapter
to the SmartPoint or RoutePoint wireless router and plug the power adapter into a
standard 120V AC power outlet, as shown in Figure 10 below. Wait 2 minutes for the
SmartPoint or RoutePoint to boot.

Figure 10

SmartPoint and RoutePoint Wireless Router AC/DC Adapter Connection

Note

The DB-9 connector marked

Factory Use Only

is a

serial port used at the factory to configure

settings and software for the SmartPoint or RoutePoint wireless router. It is not necessary to
use this port for configuration.

fhp_008

LAN port

(can accept power to unit)

fhp_009

12Vdc

jack

«
...
11
12
13
14
15
...
»

Summary of Contents for RoutePoint RP-01-00B-C-N-00



















Reviews:

No comments