background image

Farmer-Helper EFGCH Flail Mower

6

Revision 10-14-17

6. OPERATOR PROTECTIVE GEAR

The following protective clothing and gear is recommended when using your flail mower.

EYES 

-- 

Wraparound Safety Glasses or Goggles

EARS 

-- 

Ear Plugs

HANDS  -- 

Leather Gloves

FEET 

-- 

Steel-Toed Boots

LEGS 

-- 

Heavy Pants

ARMS 

-- 

Long-Sleeved Shirt

NO LOOSE CLOTHING SHOULD BE WORN AROUND THE FLAIL MOWER

7. OPERATION CHECKLIST

CAUTION

 : Look under flail mower before operating to be sure the blade area is clear.

Make sure that:

 You have completed all steps of the assembly instructions

 The PTO shaft doesn’t come apart or bottom out during the normal lifting range.

 There in no person around mower.

Remove Tractor Drawbar

During and after operation, check the grass clippings or mulched limbs for size and
quality of cut. It may be necessary to adjust the cutting height. See adjusting cutting
height.

8. Flail Mower Connection and Operation

Remember that if flail mower blades are blunted they will not cut properly. Dirt, rocks,
nails, or other foreign material will shorten blade life.

Always review the manual before operating the flail mower.

Operate mower in a safe well known area with the rear pointed away from doorways,
sidewalks, or any areas where your view is obstructed or people may approach.

Only use 540 RPM PTO 

Selection, any other use will void the warranty and may cause

severe damage to the gear box or mower.

Summary of Contents for Value Leader EFGCH Series































Reviews: