2
Housing
Polycarbonate
Colour
Red, similar to RAL 2002
Insulation class
II
Protection degree
IP 65 acc. to IEC 60529
Cable gland
intended for M20 x 1.5 or Self-sealing grommet
Volume
approx. 116 dB(A) (depending on signal tone)
Signals
32 different signal tones (see diagrams), 2nd stage can be turned on externally
Temperature range
Operation
-25 °C to +55 °C
Storage
-40 °C to +70 °C
Weight
AC 3 kg / DC 2.5 kg
Operating voltage
24 VDC, 115 VAC, 230 VAC
Connecting terminals
Clamping capacity 2.5 mm
2
solid conductor / 1.5 mm
2
stranded conductor
Flash power
5 J
Cap colours
red, yellow, green, blue, clear
Technical Data AXL08
Housing
Polycarbonate
Colour
Red, similar to RAL 2002
Insulation class
II
Protection degree
IP 65 acc. to IEC 60529
Cable gland
intended for M20 x 1.5 or Self-sealing grommet
Volume
approx. 116 dB(A) (depending on signal tone)
Signals
32 different signal tones (see diagrams), 2nd stage can be turned on externally
Temperature range
Operation
-25 °C to +55 °C
Storage
-40 °C to +70 °C
Weight
AC 2.9 kg / DC 2.4 kg
Operating voltage
24 VDC, 115 VAC, 230 VAC
Connecting terminals
Clamping capacity 2.5 mm
2
solid conductor / 1.5 mm
2
stranded conductor
Technical Data AX08
and TB4, see Fig. 2. For ac units the second stage is
available upon the application of a third wire L to TB3,
see Fig. 3.
Mounting
The AX08 / AXL08 series alarm units are mounted to a
wall or bulkhead of suitable material using the lugs
projecting from the side of the case. The lugs are bored
10 mm clearance on 250 mm centres. The recommen-
ded length of fixing screws is 30 mm. To maintain the
integrity of the weather seal, the cable entry must be via
a suitable sealed gland.
Recycling
The device may be completely recycled as electronic
waste. When the device is disassembled, plastics,
metals and electronics are to be disposed of separately.
Installation
The sounder or combined sounder strobe units can be
affixed to most surfaces using screws through the exter-
nal mounting lugs. A 20 mm gland entry is provided for
the supply cable. The cable and gland must be fitted in
accordance with the national and local regulations. It is
not necessary to earth the sounder circuitry but earth
tags should be used if earth continuity of conduit or
cable sheathing needs to be maintained..
Supply input
Ensure that the supply is correct for the voltage rating of
the sounder or combined sounder strobe being installed.
Ensure that the supply is OFF before making any
connection and wire only in accordance with the terminal
label detail.
Sound selection
Ensure the supply is OFF before proceeding. All dc and
ac units have selectable alarm sounds (see table below
for details) and are selectable by means of the 5 way DIL
switches SW1 for the first stage and SW2 for the second
stage. For dc units the second sound is made available
upon the application of a third wire connected to terminal
TB 3 as shown in Fig. 1 while still connected to terminal
TB 2. Alternatively first and second stage sound signals
can be generated by supply reversal at terminals TB3
The device complies with the requirements of the
new EMC-directive 2004/108/EC and the low voltage
directive 2006/95/EC.
The conformity with the above directives is confirmed
by the CE sign.
EMC-Directive
