background image

   14 

SUPPLEMENTAL (continued) 

FOR CASE LOADERS: 

CASE 1845C and CASE XT power units require no additional relief. 

OTHER LOADERS: 

For other makes of machines using a screw-in cartridge relief, the base end (opposite the rod end) of the tilt 
cylinder(s) needs to be protected. Contact your dealer to confirm which (plugged) port the cartridge should be 
inserted. 

Bobcat power units with BICS (Bobcat Interlock Control System) require no additional relief.  
Bobcat power units without BICS but with a plug and a relief on the tilt spool require Bobcat part # 6599161 
cartridge (to replace the plug). 

John Deere 4475, 5575, 6675, 7775, and 8875 power units require the JD part # MG86529091 cartridge. 
John Deere 240, 250, 260, 270 and 280 power units with serial number lower than 400000 must use FFC part # 
LAF4264.  
However, 200 series 4th year production models require no additional relief. These may be identified with serial 
numbers greater than: 440001 (JD240), 450001 (JD250), 460001 (JD260), 470001 (JD270), and 480001 (JD280). 
John Deere 317, 320, 325, 328 and 332 power units also require no additional relief. 

Scat Trak 1700 HD power units require no additional relief. 

GEHL 7600, 7610, 7800 & 7810 and Mustang 2095, 2099, 2105 & 2109 skidloaders can utilize a relief cartridge 
(GEHL part #138703) screwed into their main control valve opposite the existing cartridge on the tilt circuit spool, 
eliminating the need for FFC’ dual cross over relief. 

IMPORTANT

This cartridge is IN ADDITION to the existing relief cartridge, and is REQUIRED to protect 
the circuit of your power unit. Failure to install the extra cartridge 

 CAN

 result in damage to your power unit and this product and 

WILL

 void all FFC warranties 

Contact your skidloader dealer to obtain the correct relief cartridge and instructions for installation. 

Other power units require FFC part # LAF4264.  

Contact your dealer to confirm the proper relief is used. 

FOR CASE 400-SERIES 
MODELS REMOVE 
EXISTING CARTRIDGE 
AND INSTALL RELIEF 
CARTRIDGE #87445935 

Summary of Contents for LAF2301




















Reviews: