Festo VTUG M Series, Quick Start Manual

Page: 7 / 10

2.3 Valve terminal VTUG-…-M
The valve terminal VTUG-...-M (multi-pin node) has the following additional connecting
component.
1
1
Electrical multi-pin plug connection
(Sub-D or ribbon cable)
Fig. 5
2.4 Valve terminal VTUG-…-V
The valve terminal VTUG-...-V (I-Port) has the following additional connection and
display components.
2
3
3
1
1
LED X1 (status)
2
M12 plug connector
(I-Port connection)
3
Fixture for inscription field
Fig. 6
3 Multi-pin plug connection
The valve terminal VTUG-...-M can actuate up to 48 solenoid coils, depending on
the alternative connection. Each solenoid coil of the valve terminal VTUG-...-M
must be assigned to a specific pin of the multi-pin plug.
Note
No valves with 2 coils may be mounted on the valve positions that are not shown
with a grey background in the following table (Fig. 9 … Fig. 16). Coil 12 cannot be
controlled on these valve positions.
3.1 Sub-D multi-pin plug
Recommendation:
Use the following sockets with cables from the Festo range of accessories for con­
necting the valve terminal VTUG with multi-pin plug connection.
Sockets with cables
Maximum number of controllable coils 24 42
Protection class IP40 or IP67 IP40 or IP67
Sub-D socket with cable NEBV-S1...25-...- LE25 NEBV-S1...44-...- LE44
Fig. 7
3.2 Pin allocation of the multi-pin plug connections
Notes on the tables:
– Addr. = address, VP = valve position, Coil = solenoid coil
– Valve positions, which support actuation of 2 coils each, are shown with a grey
background.
Information on the above listed cables from Festo, e.g. the assignment of
the pins to the wire colour, can be found in the leaflet accompanying
the cable.
25-pin Sub-D connection on the valve terminal
Pin 14
Pin 25
Pin 1 Pin 13
Fig. 8
Pin allocation of the variants V20:
Pin Addr. Maximum number of valve positions
4, 5 … 10, 12 16 20 24
Valve position no./coil designation
1 0 0/14 0/14 0/14 0/14
2 1 0/12 0/12 0/12 23/14
3 2 1/14 1/14 1/14 1/14
4 3 1/12 1/12 1/12 22/14
5 4 2/14 2/14 2/14 2/14
6 5 2/12 2/12 2/12 21/14
7 6 3/14 3/14 3/14 3/14
8 7 3/12 3/12 3/12 20/14
9 8 4/14 4/14 4/14 4/14
10 9 4/12 4/12 19/14 19/14
11 10 5/14 5/14 5/14 5/14
12 11 5/12 5/12 18/14 18/14
13 12 6/14 6/14 6/14 6/14
14 13 6/12 6/12 17/14 17/14
15 14 7/14 7/14 7/14 7/14
16 15 7/12 7/12 16/14 16/14
17 16 8/14 8/14 8/14 8/14
18 17 8/12 15/14 15/14 15/14
19 18 9/14 9/14 9/14 9/14
20 19 9/12 14/14 14/14 14/14
21 20 10/14 10/14 10/14 10/14
22 21 10/12 13/14 13/14 13/14
23 22 11/14 11/14 11/14 11/14
24 23 11/12 12/14 12/14 12/14
25 – Com
1)
1) Connect 0 V with positive-switching control signals, 24 V with negative-switching control signals.
Fig. 9
Pin allocation of the variants V22 … V25 (not available for valve terminal for install­
ation in the control cabinet with T-profile connecting plate):
Pin Addr. Maximum number of valve positions (variant)
4, 5 … 10
(V22) 12 (V23) 16 (V24) 20 (V25)
Valve position no./coil designation
1 0 0/14 0/14 0/14 0/14
2 1 0/12 0/12 0/12 1/14
3 2 1/14 1/14 1/14 2/14
4 3 1/12 1/12 1/12 3/14
5 4 2/14 2/14 2/14 4/14
6 5 2/12 2/12 2/12 5/14
7 6 3/14 3/14 3/14 6/14
8 7 3/12 3/12 3/12 7/14
9 8 4/14 4/14 4/14 8/14
10 9 4/12 4/12 5/14 9/14
11 10 5/14 5/14 6/14 10/14
12 11 5/12 5/12 7/14 11/14
13 12 6/14 6/14 8/14 12/14
14 13 6/12 6/12 9/14 13/14
15 14 7/14 7/14 10/14 14/14
16 15 7/12 7/12 11/14 15/14
17 16 8/14 8/14 12/14 16/14
18 17 8/12 9/14 13/14 17/14
19 18 9/14 10/14 14/14 18/14
20 19 9/12 11/14 15/14 19/14
21 – Com for coil 16 … 19
1)
22 – Com for coil 12 … 15
1)
23 – Com for coil 8 … 11
1)
24 – Com for coil 4 … 7
1)
25 – Com for coil 0 … 3
1)
1) Connect 0 V with positive-switching control signals, 24 V with negative-switching control signals.
Fig. 10